The following warnings occurred:
Warning [2] count(): Parameter must be an array or an object that implements Countable - Line: 864 - File: showthread.php PHP 7.4.33 (FreeBSD)
File Line Function
/showthread.php 864 errorHandler->error



MetalworkingFun Forum › Machining › Projects v
Making New Gear Change Handles

Thread Modes
Making New Gear Change Handles
EdK Offline
Whipping Boy
*******
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#1
03-23-2013, 03:40 PM
I've been wanting to make some new gear change handles for the mill for a couple of years now since the factory installed handles are plastic and do not hold tight to the shaft. I'm going to make the new ones out of aluminum and pin them to the shaft with a roll pin. I got started on the project today.

Ed

       
Reply
Thanks given by:


Messages In This Thread
Making New Gear Change Handles - by EdK - 03-23-2013, 03:40 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 03:44 PM
RE: Making New Gear Change Handles - by Bill Gruby - 03-23-2013, 03:46 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 04:02 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 04:57 PM
RE: Making New Gear Change Handles - by f350ca - 03-23-2013, 06:10 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 07:09 PM
RE: Making New Gear Change Handles - by stevec - 03-23-2013, 06:50 PM
RE: Making New Gear Change Handles - by EdK - 03-23-2013, 07:07 PM
RE: Making New Gear Change Handles - by TomG - 03-24-2013, 09:28 AM
RE: Making New Gear Change Handles - by EdK - 03-24-2013, 09:31 AM
RE: Making New Gear Change Handles - by EdK - 03-30-2013, 05:05 PM
RE: Making New Gear Change Handles - by Bill Gruby - 03-30-2013, 05:59 PM
RE: Making New Gear Change Handles - by TomG - 03-30-2013, 07:02 PM
RE: Making New Gear Change Handles - by EdK - 03-30-2013, 08:29 PM
RE: Making New Gear Change Handles - by Mayhem - 03-30-2013, 08:36 PM
RE: Making New Gear Change Handles - by EdK - 04-07-2013, 01:19 PM
RE: Making New Gear Change Handles - by f350ca - 04-07-2013, 04:35 PM
RE: Making New Gear Change Handles - by Bill Gruby - 04-07-2013, 05:51 PM
RE: Making New Gear Change Handles - by DaveH - 04-08-2013, 08:06 PM
RE: Making New Gear Change Handles - by PixMan - 04-08-2013, 08:38 PM
RE: Making New Gear Change Handles - by EdK - 04-09-2013, 06:38 AM
RE: Making New Gear Change Handles - by sasquatch - 04-09-2013, 07:31 AM
RE: Making New Gear Change Handles - by Mayhem - 04-09-2013, 07:48 AM
RE: Making New Gear Change Handles - by Dave J - 04-09-2013, 08:42 AM
RE: Making New Gear Change Handles - by EdK - 04-09-2013, 10:22 AM
RE: Making New Gear Change Handles - by Mayhem - 04-09-2013, 10:40 AM
RE: Making New Gear Change Handles - by EdK - 04-09-2013, 11:30 AM



Users browsing this thread: 1 Guest(s)