MetalworkingFun Forum › Machinery › Lathes v
Metal gears for 7x12s

Thread Modes
Metal gears for 7x12s
sasquatch Offline
Senior
*****
Posts: 825
Threads: 25
Joined: Jul 2012
Location: N. Bay Ontario
#9
03-16-2013, 07:56 PM
JMO, Yup, just my opinion,, which at times is about equal to the round number below one.


HOWEVER,, I,m sticking to it!! Lol
sasquatch, proud to be a member of MetalworkingFun since Jul 2012.
Reply
Thanks given by:


Messages In This Thread
Metal gears for 7x12s - by Brian - 03-15-2013, 11:43 AM
RE: Metal gears for 7x12s - by EdK - 03-15-2013, 12:57 PM
RE: Metal gears for 7x12s - by stevec - 03-15-2013, 03:09 PM
RE: Metal gears for 7x12s - by sasquatch - 03-15-2013, 06:51 PM
RE: Metal gears for 7x12s - by stevec - 03-15-2013, 07:16 PM
RE: Metal gears for 7x12s - by EdK - 03-15-2013, 07:48 PM
RE: Metal gears for 7x12s - by EdK - 03-15-2013, 07:00 PM
RE: Metal gears for 7x12s - by dallen - 03-15-2013, 10:03 PM
RE: Metal gears for 7x12s - by sasquatch - 03-16-2013, 07:56 PM
RE: Metal gears for 7x12s - by Brian - 03-17-2013, 03:39 AM
RE: Metal gears for 7x12s - by Brian - 03-17-2013, 03:59 AM
RE: Metal gears for 7x12s - by Sunset Machine - 03-17-2013, 09:57 AM
RE: Metal gears for 7x12s - by stevec - 03-17-2013, 06:52 AM
RE: Metal gears for 7x12s - by EdK - 03-17-2013, 10:28 AM
RE: Metal gears for 7x12s - by EdK - 03-17-2013, 10:27 AM
RE: Metal gears for 7x12s - by stevec - 03-17-2013, 01:59 PM
RE: Metal gears for 7x12s - by Brian - 03-17-2013, 04:13 PM
RE: Metal gears for 7x12s - by stevec - 03-17-2013, 06:30 PM
RE: Metal gears for 7x12s - by Brian - 03-18-2013, 09:12 AM
RE: Metal gears for 7x12s - by sasquatch - 03-17-2013, 07:14 PM
RE: Metal gears for 7x12s - by stevec - 03-18-2013, 03:58 PM
RE: Metal gears for 7x12s - by Brian - 03-26-2013, 03:51 AM
RE: Metal gears for 7x12s - by Brian - 04-07-2013, 03:04 AM
RE: Metal gears for 7x12s - by EdK - 04-07-2013, 09:07 AM
RE: Metal gears for 7x12s - by Brian - 04-07-2013, 01:24 PM
RE: Metal gears for 7x12s - by Dave J - 04-07-2013, 08:20 AM
RE: Metal gears for 7x12s - by Brian - 04-17-2013, 04:43 PM



Users browsing this thread: 1 Guest(s)