MetalworkingFun Forum › Machinery › Lathes › Lathe Tooling v
ER-40 Collet Chuck For My Lathe

Thread Modes
ER-40 Collet Chuck For My Lathe
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#50
03-11-2013, 07:53 AM
(03-09-2013, 08:29 PM)EdK Wrote: I chucked up a gauge pin and it shows the same run-out as the ER taper so good enough for this old fart! Happyyes

Ed

Show off..... Big Grin

Great job Ed. Smiley-eatdrink004
Willie
Reply
Thanks given by: EdK


Messages In This Thread
ER-40 Collet Chuck For My Lathe - by EdK - 09-07-2012, 04:05 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-07-2012, 04:26 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-07-2012, 07:14 PM
RE: ER-40 Collet Chuck For My Lathe - by PixMan - 09-07-2012, 08:23 PM
RE: ER-40 Collet Chuck For My Lathe - by DaveH - 09-08-2012, 07:26 AM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-08-2012, 08:32 AM
RE: ER-40 Collet Chuck For My Lathe - by PixMan - 09-08-2012, 07:36 AM
RE: ER-40 Collet Chuck For My Lathe - by pineyfolks - 09-08-2012, 08:07 AM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-08-2012, 08:38 AM
RE: ER-40 Collet Chuck For My Lathe - by DaveH - 09-08-2012, 01:45 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-12-2012, 06:42 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-12-2012, 07:09 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-13-2012, 05:27 AM
RE: ER-40 Collet Chuck For My Lathe - by PixMan - 09-13-2012, 04:46 PM
RE: ER-40 Collet Chuck For My Lathe - by f350ca - 09-13-2012, 06:39 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-13-2012, 07:12 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 09-23-2012, 01:04 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 12-21-2012, 12:38 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 12-28-2012, 05:04 PM
RE: ER-40 Collet Chuck For My Lathe - by Dave J - 12-28-2012, 07:56 PM
RE: ER-40 Collet Chuck For My Lathe - by f350ca - 12-28-2012, 08:21 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 12-28-2012, 08:31 PM
RE: ER-40 Collet Chuck For My Lathe - by Dave J - 12-29-2012, 06:48 AM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 12-29-2012, 10:36 AM
RE: ER-40 Collet Chuck For My Lathe - by Dave J - 12-29-2012, 08:29 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 12-30-2012, 10:34 AM
RE: ER-40 Collet Chuck For My Lathe - by stevec - 12-30-2012, 01:42 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 03-09-2013, 04:38 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 03-09-2013, 05:22 PM
RE: ER-40 Collet Chuck For My Lathe - by stevec - 03-09-2013, 05:20 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 03-09-2013, 05:24 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 03-09-2013, 06:01 PM
RE: ER-40 Collet Chuck For My Lathe - by krv3000 - 03-09-2013, 06:01 PM
RE: ER-40 Collet Chuck For My Lathe - by DaveH - 03-09-2013, 06:49 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 03-09-2013, 08:29 PM
RE: ER-40 Collet Chuck For My Lathe - by Highpower - 03-11-2013, 07:53 AM
RE: ER-40 Collet Chuck For My Lathe - by Mayhem - 03-09-2013, 08:35 PM
RE: ER-40 Collet Chuck For My Lathe - by krv3000 - 03-10-2013, 06:11 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 03-10-2013, 07:28 PM
RE: ER-40 Collet Chuck For My Lathe - by EdK - 03-11-2013, 10:45 AM



Users browsing this thread: 24 Guest(s)