MetalworkingFun Forum › Machining › Projects v
Bandsaw Conversion

Thread Modes
Bandsaw Conversion
Bill Gruby
Unregistered
 
#32
12-31-2012, 06:41 PM
I have 3 of them in different sizes. They measure RPM or SFPM.

OK it's all over but the shouting. New 14 TPI blade cut thru 3/8 X 3 X 3 7075 Aluminum scrap piece in 51 seconds flat. It was well worth the effort.

"Billy G"


Attached Files Thumbnail(s)
   
Reply
Thanks given by:


Messages In This Thread
Bandsaw Conversion - by Bill Gruby - 12-23-2012, 10:30 AM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:21 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:22 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:26 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:28 PM
RE: Bandsaw Conversion - by ml_woy - 12-24-2012, 11:36 AM
RE: Bandsaw Conversion - by Bill Gruby - 12-24-2012, 05:10 PM
RE: Bandsaw Conversion - by EdK - 12-23-2012, 02:19 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 02:26 PM
RE: Bandsaw Conversion - by DaveH - 12-23-2012, 03:42 PM
RE: Bandsaw Conversion - by sasquatch - 12-23-2012, 04:45 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 05:07 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 05:41 PM
RE: Bandsaw Conversion - by DanH - 12-23-2012, 05:42 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 05:59 PM
RE: Bandsaw Conversion - by DanH - 12-23-2012, 06:29 PM
RE: Bandsaw Conversion - by f350ca - 12-23-2012, 10:09 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 10:45 PM
RE: Bandsaw Conversion - by f350ca - 12-23-2012, 10:50 PM
RE: Bandsaw Conversion - by stevec - 12-24-2012, 08:57 AM
RE: Bandsaw Conversion - by stevec - 12-24-2012, 10:18 AM
RE: Bandsaw Conversion - by EdK - 12-24-2012, 10:40 AM
RE: Bandsaw Conversion - by stevec - 12-24-2012, 10:45 AM
RE: Bandsaw Conversion - by sasquatch - 12-24-2012, 05:14 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-26-2012, 09:34 AM
RE: Bandsaw Conversion - by Bill Gruby - 12-30-2012, 05:14 PM
RE: Bandsaw Conversion - by sasquatch - 12-30-2012, 10:02 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-31-2012, 04:43 AM
RE: Bandsaw Conversion - by Bill Gruby - 12-31-2012, 09:51 AM
RE: Bandsaw Conversion - by DaveH - 12-31-2012, 12:02 PM
RE: Bandsaw Conversion - by sasquatch - 12-31-2012, 03:26 PM
RE: Bandsaw Conversion - by Bill Gruby - 12-31-2012, 06:41 PM
RE: Bandsaw Conversion - by sasquatch - 12-31-2012, 07:27 PM
RE: Bandsaw Conversion - by krv3000 - 01-01-2013, 03:17 PM
RE: Bandsaw Conversion - by Bill Gruby - 01-01-2013, 04:11 PM
RE: Bandsaw Conversion - by DaveH - 01-01-2013, 04:48 PM
RE: Bandsaw Conversion - by monkers - 02-02-2013, 11:07 AM
RE: Bandsaw Conversion - by Bill Gruby - 02-02-2013, 01:24 PM



Users browsing this thread: 1 Guest(s)