Bandsaw Conversion

Hello There, Guest! Register

Thread Modes

Bandsaw Conversion

Bill Gruby
Unregistered

#11

12-23-2012, 05:41 PM

If my math is correct the motor is 1725 RPM, Gear reduction is 60:1. that gives you approximately 29 RPM out of the reduction unit. Rounding blade length to 96 inches. That is 8 ft so 8X29= 232 FPM if I go 1:1 to the drive pulley. It works for me.

"Billy G"

Reply

« Next Oldest | Next Newest »

Messages In This Thread

Bandsaw Conversion - by Bill Gruby - 12-23-2012, 10:30 AM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:21 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:22 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:26 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 01:28 PM

RE: Bandsaw Conversion - by ml_woy - 12-24-2012, 11:36 AM

RE: Bandsaw Conversion - by Bill Gruby - 12-24-2012, 05:10 PM

RE: Bandsaw Conversion - by EdK - 12-23-2012, 02:19 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 02:26 PM

RE: Bandsaw Conversion - by DaveH - 12-23-2012, 03:42 PM

RE: Bandsaw Conversion - by sasquatch - 12-23-2012, 04:45 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 05:07 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 05:41 PM

RE: Bandsaw Conversion - by DanH - 12-23-2012, 05:42 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 05:59 PM

RE: Bandsaw Conversion - by DanH - 12-23-2012, 06:29 PM

RE: Bandsaw Conversion - by f350ca - 12-23-2012, 10:09 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-23-2012, 10:45 PM

RE: Bandsaw Conversion - by f350ca - 12-23-2012, 10:50 PM

RE: Bandsaw Conversion - by stevec - 12-24-2012, 08:57 AM

RE: Bandsaw Conversion - by stevec - 12-24-2012, 10:18 AM

RE: Bandsaw Conversion - by EdK - 12-24-2012, 10:40 AM

RE: Bandsaw Conversion - by stevec - 12-24-2012, 10:45 AM

RE: Bandsaw Conversion - by sasquatch - 12-24-2012, 05:14 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-26-2012, 09:34 AM

RE: Bandsaw Conversion - by Bill Gruby - 12-30-2012, 05:14 PM

RE: Bandsaw Conversion - by sasquatch - 12-30-2012, 10:02 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-31-2012, 04:43 AM

RE: Bandsaw Conversion - by Bill Gruby - 12-31-2012, 09:51 AM

RE: Bandsaw Conversion - by DaveH - 12-31-2012, 12:02 PM

RE: Bandsaw Conversion - by sasquatch - 12-31-2012, 03:26 PM

RE: Bandsaw Conversion - by Bill Gruby - 12-31-2012, 06:41 PM

RE: Bandsaw Conversion - by sasquatch - 12-31-2012, 07:27 PM

RE: Bandsaw Conversion - by krv3000 - 01-01-2013, 03:17 PM

RE: Bandsaw Conversion - by Bill Gruby - 01-01-2013, 04:11 PM

RE: Bandsaw Conversion - by DaveH - 01-01-2013, 04:48 PM

RE: Bandsaw Conversion - by monkers - 02-02-2013, 11:07 AM

RE: Bandsaw Conversion - by Bill Gruby - 02-02-2013, 01:24 PM

Users browsing this thread: 3 Guest(s)