|
Shop Press
|
12-17-2012, 08:26 PM
Picked up this press plate on ebay. Made from 410 SS with 15 holes. The largest is 2". Will work great with my little arbor press also...Bob
Bob Wright
Metal Master Fab Salem Ohio Birthplace of the Silver and Deming drill bit. 5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders... |
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Shop Press - by aametalmaster - 11-25-2012, 12:39 PM
RE: Shop Press - by ETC57 - 11-25-2012, 01:52 PM
RE: Shop Press - by aametalmaster - 11-25-2012, 02:08 PM
RE: Shop Press - by sasquatch - 11-25-2012, 04:36 PM
RE: Shop Press - by Mayhem - 11-26-2012, 07:38 AM
RE: Shop Press - by stevec - 11-26-2012, 09:35 AM
RE: Shop Press - by aametalmaster - 12-02-2012, 03:13 PM
RE: Shop Press - by EdK - 12-02-2012, 03:48 PM
RE: Shop Press - by DaveH - 12-02-2012, 03:54 PM
RE: Shop Press - by sasquatch - 12-02-2012, 06:02 PM
RE: Shop Press - by starlight_tools - 12-02-2012, 10:10 PM
RE: Shop Press - by aametalmaster - 12-03-2012, 07:27 PM
RE: Shop Press - by EdK - 12-04-2012, 06:39 AM
RE: Shop Press - by aametalmaster - 12-04-2012, 05:19 PM
RE: Shop Press - by stevec - 12-05-2012, 09:03 AM
RE: Shop Press - by aametalmaster - 12-05-2012, 05:17 PM
RE: Shop Press - by Mayhem - 12-05-2012, 09:31 AM
RE: Shop Press - by aametalmaster - 12-09-2012, 01:46 PM
RE: Shop Press - by DaveH - 12-09-2012, 02:28 PM
RE: Shop Press - by aametalmaster - 12-09-2012, 04:08 PM
RE: Shop Press - by DaveH - 12-09-2012, 05:15 PM
RE: Shop Press - by aametalmaster - 12-17-2012, 08:26 PM
RE: Shop Press - by starlight_tools - 12-18-2012, 01:24 AM
RE: Shop Press - by stevec - 12-18-2012, 09:01 AM
RE: Shop Press - by EdK - 12-18-2012, 10:11 AM
RE: Shop Press - by sasquatch - 12-18-2012, 03:58 PM
RE: Shop Press - by aametalmaster - 12-23-2012, 03:28 PM
RE: Shop Press - by sasquatch - 12-23-2012, 04:41 PM
RE: Shop Press - by f350ca - 12-23-2012, 06:05 PM
RE: Shop Press - by aametalmaster - 12-23-2012, 07:54 PM
RE: Shop Press - by f350ca - 12-23-2012, 10:00 PM
RE: Shop Press - by aametalmaster - 12-25-2012, 12:29 PM
RE: Shop Press - by sasquatch - 12-25-2012, 06:11 PM
RE: Shop Press - by DaveH - 12-26-2012, 06:37 AM
RE: Shop Press - by aametalmaster - 01-31-2013, 07:04 PM
RE: Shop Press - by EdK - 01-31-2013, 07:23 PM
RE: Shop Press - by sasquatch - 01-31-2013, 07:43 PM
RE: Shop Press - by starlight_tools - 02-01-2013, 09:12 PM
RE: Shop Press - by aametalmaster - 08-24-2013, 11:35 AM
RE: Shop Press - by starlight_tools - 08-24-2013, 12:06 PM
RE: Shop Press - by aametalmaster - 08-24-2013, 11:31 AM
RE: Shop Press - by DaveH - 07-29-2014, 01:33 PM
RE: Shop Press - by EdK - 07-29-2014, 04:57 PM
RE: Shop Press - by ETC57 - 07-31-2014, 03:26 PM
|
