MetalworkingFun Forum › Machining › General Metalworking Discussion v
How To Make A Flat Bottom Hole

Thread Modes
How To Make A Flat Bottom Hole
petertha Offline
Freshman
**
Posts: 32
Threads: 3
Joined: Sep 2012
Location: Calgary, AB, Canada
#27
12-14-2012, 03:35 PM
Because you mentioned vice stop, Ill attach a pic of one I made recently just for other ideas. But if I had to make it again, I would extend the slit past the 1/4" rod hole. Because... the steel is from 5/8" stock & I have to torque the two 8-32 capscrews pretty good to lock the rod down (ie a lot of strength/resistance from the steel itself).


Attached Files Thumbnail(s)
   
petertha, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:


Messages In This Thread
How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 08:23 AM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-13-2012, 08:26 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:19 AM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:39 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:05 PM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 08:46 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 09:31 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by f350ca - 12-13-2012, 10:12 AM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 11:33 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 12:19 PM
RE: How To Make A Flat Bottom Hole - by Arbalest - 12-13-2012, 01:07 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 01:10 PM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:41 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:07 PM
RE: How To Make A Flat Bottom Hole - by DaveH - 12-13-2012, 01:22 PM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 01:59 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-13-2012, 05:52 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:10 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 05:00 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-14-2012, 05:29 PM
RE: How To Make A Flat Bottom Hole - by Mayhem - 12-13-2012, 10:07 PM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-13-2012, 10:59 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 06:55 AM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-14-2012, 07:50 AM
RE: How To Make A Flat Bottom Hole - by petertha - 12-14-2012, 03:35 PM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-14-2012, 05:20 PM



Users browsing this thread: 8 Guest(s)