MetalworkingFun Forum › Machining › General Metalworking Discussion v
How To Make A Flat Bottom Hole

Thread Modes
How To Make A Flat Bottom Hole
Sunset Machine Offline
Junior
****
Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA
#3
12-13-2012, 08:30 AM (This post was last modified: 12-13-2012, 08:43 AM by Sunset Machine.)
I'd like to see that too, maybe a plug pressed in from the left or pre-drill and grind up a drill bit for a couple of guesses. Luck out and find a counterbore that would fit? This one is $25.

http://www.travers.com/product.asp?eapro...%2F4%22%27
Reply
Thanks given by:


Messages In This Thread
How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 08:23 AM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-13-2012, 08:26 AM
RE: How To Make A Flat Bottom Hole - by Sunset Machine - 12-13-2012, 08:30 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:19 AM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:39 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:05 PM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 08:46 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 09:31 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 09:23 AM
RE: How To Make A Flat Bottom Hole - by f350ca - 12-13-2012, 10:12 AM
RE: How To Make A Flat Bottom Hole - by dallen - 12-13-2012, 11:33 AM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 12:19 PM
RE: How To Make A Flat Bottom Hole - by Arbalest - 12-13-2012, 01:07 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 01:10 PM
RE: How To Make A Flat Bottom Hole - by arvidj - 12-13-2012, 02:41 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:07 PM
RE: How To Make A Flat Bottom Hole - by DaveH - 12-13-2012, 01:22 PM
RE: How To Make A Flat Bottom Hole - by rleete - 12-13-2012, 01:59 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-13-2012, 05:52 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-13-2012, 06:10 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 05:00 PM
RE: How To Make A Flat Bottom Hole - by TomG - 12-14-2012, 05:29 PM
RE: How To Make A Flat Bottom Hole - by Mayhem - 12-13-2012, 10:07 PM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-13-2012, 10:59 PM
RE: How To Make A Flat Bottom Hole - by EdK - 12-14-2012, 06:55 AM
RE: How To Make A Flat Bottom Hole - by PixMan - 12-14-2012, 07:50 AM
RE: How To Make A Flat Bottom Hole - by petertha - 12-14-2012, 03:35 PM
RE: How To Make A Flat Bottom Hole - by sasquatch - 12-14-2012, 05:20 PM



Users browsing this thread: 6 Guest(s)