Shop Press
#18
Made the tooling rack but the 1" bars just fell thru the 1" punched holes. So i bored some 1" threaded nuts out and added a set screw to lock them to the shaft. That way the nuts act as keepers holding the bars in the rack...Bob


Attached Files Thumbnail(s)
       
Bob Wright
Metal Master Fab
Salem Ohio
Birthplace of the Silver and Deming drill bit.
5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders...
Reply
Thanks given by:


Messages In This Thread
Shop Press - by aametalmaster - 11-25-2012, 12:39 PM
RE: Shop Press - by ETC57 - 11-25-2012, 01:52 PM
RE: Shop Press - by aametalmaster - 11-25-2012, 02:08 PM
RE: Shop Press - by sasquatch - 11-25-2012, 04:36 PM
RE: Shop Press - by Mayhem - 11-26-2012, 07:38 AM
RE: Shop Press - by stevec - 11-26-2012, 09:35 AM
RE: Shop Press - by aametalmaster - 12-02-2012, 03:13 PM
RE: Shop Press - by EdK - 12-02-2012, 03:48 PM
RE: Shop Press - by DaveH - 12-02-2012, 03:54 PM
RE: Shop Press - by sasquatch - 12-02-2012, 06:02 PM
RE: Shop Press - by starlight_tools - 12-02-2012, 10:10 PM
RE: Shop Press - by aametalmaster - 12-03-2012, 07:27 PM
RE: Shop Press - by EdK - 12-04-2012, 06:39 AM
RE: Shop Press - by aametalmaster - 12-04-2012, 05:19 PM
RE: Shop Press - by stevec - 12-05-2012, 09:03 AM
RE: Shop Press - by aametalmaster - 12-05-2012, 05:17 PM
RE: Shop Press - by Mayhem - 12-05-2012, 09:31 AM
RE: Shop Press - by aametalmaster - 12-09-2012, 01:46 PM
RE: Shop Press - by DaveH - 12-09-2012, 02:28 PM
RE: Shop Press - by aametalmaster - 12-09-2012, 04:08 PM
RE: Shop Press - by DaveH - 12-09-2012, 05:15 PM
RE: Shop Press - by aametalmaster - 12-17-2012, 08:26 PM
RE: Shop Press - by starlight_tools - 12-18-2012, 01:24 AM
RE: Shop Press - by stevec - 12-18-2012, 09:01 AM
RE: Shop Press - by EdK - 12-18-2012, 10:11 AM
RE: Shop Press - by sasquatch - 12-18-2012, 03:58 PM
RE: Shop Press - by aametalmaster - 12-23-2012, 03:28 PM
RE: Shop Press - by sasquatch - 12-23-2012, 04:41 PM
RE: Shop Press - by f350ca - 12-23-2012, 06:05 PM
RE: Shop Press - by aametalmaster - 12-23-2012, 07:54 PM
RE: Shop Press - by f350ca - 12-23-2012, 10:00 PM
RE: Shop Press - by aametalmaster - 12-25-2012, 12:29 PM
RE: Shop Press - by sasquatch - 12-25-2012, 06:11 PM
RE: Shop Press - by DaveH - 12-26-2012, 06:37 AM
RE: Shop Press - by aametalmaster - 01-31-2013, 07:04 PM
RE: Shop Press - by EdK - 01-31-2013, 07:23 PM
RE: Shop Press - by sasquatch - 01-31-2013, 07:43 PM
RE: Shop Press - by starlight_tools - 02-01-2013, 09:12 PM
RE: Shop Press - by aametalmaster - 08-24-2013, 11:35 AM
RE: Shop Press - by starlight_tools - 08-24-2013, 12:06 PM
RE: Shop Press - by aametalmaster - 08-24-2013, 11:31 AM
RE: Shop Press - by DaveH - 07-29-2014, 01:33 PM
RE: Shop Press - by EdK - 07-29-2014, 04:57 PM
RE: Shop Press - by ETC57 - 07-31-2014, 03:26 PM



Users browsing this thread: 1 Guest(s)