MetalworkingFun Forum › Machinery › Lathes › Lathe Tooling v
Lay down insert threading tools

Thread Modes
Lay down insert threading tools
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#28
10-30-2012, 07:43 AM
(10-29-2012, 06:25 PM)PixMan Wrote: Done! Thanks for the pointer to the right place, Ed.

They were two pages I printed out shortly after I downloaded that catalog. Much easier that swirling your fingers throught the air and hoping that you have it right.
Hunting American dentists since 2015.
Reply
Thanks given by:


Messages In This Thread
Lay down insert threading tools - by Mayhem - 03-29-2012, 05:09 AM
RE: Lay down insert threading tools - by EdK - 03-29-2012, 06:48 AM
RE: Lay down insert threading tools - by Mayhem - 03-29-2012, 07:39 AM
RE: Lay down insert threading tools - by EdK - 03-29-2012, 07:49 AM
RE: Lay down insert threading tools - by DaveH - 03-29-2012, 07:57 AM
RE: Lay down insert threading tools - by Mayhem - 03-29-2012, 08:18 AM
RE: Lay down insert threading tools - by PixMan - 03-31-2012, 10:47 AM
RE: Lay down insert threading tools - by EdK - 03-31-2012, 12:58 PM
RE: Lay down insert threading tools - by DaveH - 03-31-2012, 10:59 AM
RE: Lay down insert threading tools - by ETC57 - 03-31-2012, 11:56 AM
RE: Lay down insert threading tools - by Mayhem - 03-31-2012, 11:58 AM
RE: Lay down insert threading tools - by DaveH - 03-31-2012, 12:07 PM
RE: Lay down insert threading tools - by PixMan - 03-31-2012, 03:11 PM
RE: Lay down insert threading tools - by EdK - 03-31-2012, 03:22 PM
RE: Lay down insert threading tools - by PixMan - 03-31-2012, 03:25 PM
RE: Lay down insert threading tools - by EdK - 03-31-2012, 03:26 PM
RE: Lay down insert threading tools - by PixMan - 03-31-2012, 07:45 PM
RE: Lay down insert threading tools - by EdK - 03-31-2012, 07:54 PM
RE: Lay down insert threading tools - by DaveH - 10-21-2012, 12:12 PM
RE: Lay down insert threading tools - by stevec - 10-21-2012, 02:01 PM
RE: Lay down insert threading tools - by EdK - 10-21-2012, 02:41 PM
RE: Lay down insert threading tools - by PixMan - 10-29-2012, 05:01 PM
RE: Lay down insert threading tools - by EdK - 10-29-2012, 05:23 PM
RE: Lay down insert threading tools - by EdK - 10-29-2012, 05:38 PM
RE: Lay down insert threading tools - by PixMan - 10-29-2012, 06:25 PM
RE: Lay down insert threading tools - by Mayhem - 10-30-2012, 07:43 AM
RE: Lay down insert threading tools - by stevec - 10-30-2012, 08:39 AM
RE: Lay down insert threading tools - by PixMan - 10-30-2012, 04:57 PM
RE: Lay down insert threading tools - by stevec - 10-30-2012, 05:52 PM



Users browsing this thread: 21 Guest(s)