|
Acme Threads
|
09-28-2012, 02:53 PM
Dallen, I'm not sure not sure I follow. Are you talking about grinding groove long the top of the tool? As far as the edges are concerned, they need to stay sharp, as they are cutting too. There shouldn't be any square edges on the tool. It will have a small clearance to accommodate the helix angle of the cut, but nothing more.
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
Acme Threads - by dallen - 09-26-2012, 01:11 PM
RE: Acme Threads - by EdK - 09-26-2012, 02:06 PM
RE: Acme Threads - by dallen - 09-26-2012, 02:59 PM
RE: Acme Threads - by stevec - 09-26-2012, 03:39 PM
RE: Acme Threads - by doubleboost - 09-26-2012, 03:23 PM
RE: Acme Threads - by dallen - 09-26-2012, 04:39 PM
RE: Acme Threads - by doubleboost - 09-26-2012, 04:46 PM
RE: Acme Threads - by dallen - 09-26-2012, 07:27 PM
RE: Acme Threads - by EdK - 09-26-2012, 07:35 PM
RE: Acme Threads - by dallen - 09-26-2012, 08:01 PM
RE: Acme Threads - by TomG - 09-26-2012, 09:20 PM
RE: Acme Threads - by EdK - 09-27-2012, 05:53 AM
RE: Acme Threads - by TomG - 09-27-2012, 06:24 AM
RE: Acme Threads - by EdK - 09-27-2012, 06:43 AM
RE: Acme Threads - by stevec - 09-27-2012, 06:50 AM
RE: Acme Threads - by EdK - 09-27-2012, 06:52 AM
RE: Acme Threads - by Highpower - 09-27-2012, 08:40 AM
RE: Acme Threads - by TomG - 09-27-2012, 08:48 AM
RE: Acme Threads - by stevec - 09-27-2012, 08:48 AM
RE: Acme Threads - by EdK - 09-27-2012, 09:38 AM
RE: Acme Threads - by dallen - 09-27-2012, 11:51 AM
RE: Acme Threads - by Tony Wells - 09-27-2012, 10:33 PM
RE: Acme Threads - by dallen - 09-28-2012, 08:30 AM
RE: Acme Threads - by Tony Wells - 09-28-2012, 02:53 PM
RE: Acme Threads - by dallen - 09-28-2012, 07:09 PM
RE: Acme Threads - by ScrapMetal - 09-30-2012, 10:08 AM
RE: Acme Threads - by TomG - 09-30-2012, 10:43 AM
RE: Acme Threads - by dallen - 09-30-2012, 03:01 PM
RE: Acme Threads - by PixMan - 09-30-2012, 07:27 PM
RE: Acme Threads - by EdK - 10-01-2012, 05:49 AM
RE: Acme Threads - by big job - 10-01-2012, 05:23 AM
RE: Acme Threads - by dallen - 10-11-2012, 06:41 PM
RE: Acme Threads - by EdK - 10-12-2012, 05:44 AM
RE: Acme Threads - by DaveH - 10-12-2012, 05:56 AM
RE: Acme Threads - by dallen - 10-12-2012, 06:27 AM
RE: Acme Threads - by doubleboost - 10-16-2012, 03:56 PM
RE: Acme Threads - by dallen - 10-16-2012, 07:29 PM
|
