MetalworkingFun Forum › Machining › How-To's v
Acme Threads

Thread Modes
Acme Threads
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#16
09-27-2012, 06:52 AM
(09-27-2012, 06:50 AM)stevec Wrote: Ed, remember the nut that will follow.
It can be done though, I cut a new nut for the cross feed screw on my 12x36, came out pretty good ( it's left hand too).

Good point Steve. The nut would be the challenge compared to the screw. I'll have to think about that one. Chin

Ed
Reply
Thanks given by:


Messages In This Thread
Acme Threads - by dallen - 09-26-2012, 01:11 PM
RE: Acme Threads - by EdK - 09-26-2012, 02:06 PM
RE: Acme Threads - by dallen - 09-26-2012, 02:59 PM
RE: Acme Threads - by stevec - 09-26-2012, 03:39 PM
RE: Acme Threads - by doubleboost - 09-26-2012, 03:23 PM
RE: Acme Threads - by dallen - 09-26-2012, 04:39 PM
RE: Acme Threads - by doubleboost - 09-26-2012, 04:46 PM
RE: Acme Threads - by dallen - 09-26-2012, 07:27 PM
RE: Acme Threads - by EdK - 09-26-2012, 07:35 PM
RE: Acme Threads - by dallen - 09-26-2012, 08:01 PM
RE: Acme Threads - by TomG - 09-26-2012, 09:20 PM
RE: Acme Threads - by EdK - 09-27-2012, 05:53 AM
RE: Acme Threads - by TomG - 09-27-2012, 06:24 AM
RE: Acme Threads - by EdK - 09-27-2012, 06:43 AM
RE: Acme Threads - by stevec - 09-27-2012, 06:50 AM
RE: Acme Threads - by EdK - 09-27-2012, 06:52 AM
RE: Acme Threads - by Highpower - 09-27-2012, 08:40 AM
RE: Acme Threads - by TomG - 09-27-2012, 08:48 AM
RE: Acme Threads - by stevec - 09-27-2012, 08:48 AM
RE: Acme Threads - by EdK - 09-27-2012, 09:38 AM
RE: Acme Threads - by dallen - 09-27-2012, 11:51 AM
RE: Acme Threads - by Tony Wells - 09-27-2012, 10:33 PM
RE: Acme Threads - by dallen - 09-28-2012, 08:30 AM
RE: Acme Threads - by Tony Wells - 09-28-2012, 02:53 PM
RE: Acme Threads - by dallen - 09-28-2012, 07:09 PM
RE: Acme Threads - by ScrapMetal - 09-30-2012, 10:08 AM
RE: Acme Threads - by TomG - 09-30-2012, 10:43 AM
RE: Acme Threads - by dallen - 09-30-2012, 03:01 PM
RE: Acme Threads - by PixMan - 09-30-2012, 07:27 PM
RE: Acme Threads - by EdK - 10-01-2012, 05:49 AM
RE: Acme Threads - by big job - 10-01-2012, 05:23 AM
RE: Acme Threads - by dallen - 10-11-2012, 06:41 PM
RE: Acme Threads - by EdK - 10-12-2012, 05:44 AM
RE: Acme Threads - by DaveH - 10-12-2012, 05:56 AM
RE: Acme Threads - by dallen - 10-12-2012, 06:27 AM
RE: Acme Threads - by doubleboost - 10-16-2012, 03:56 PM
RE: Acme Threads - by dallen - 10-16-2012, 07:29 PM



Users browsing this thread: 4 Guest(s)