Harrison L5 lathe rebuild
#32
Thanks for all the nice comments lads WorthyWorthy I am glad the project is of interest to people out there, I have watched plenty other peoples projects and enjoyed them so its nice to know I am putting a bit back into the systemSmile

Hi SteveC , The lathe had the chuck guard on it when I got it and it is handy when using suds , just stops a lot of it going all over and also making sure it gets back to the pump, as Tom says as long as it is out the way and also not in the way, its there when you need it and no bother if you dont need it. I am planning on keeping the lathe 'forever' so doing the likes of the splash guard are worth doing and jobs you would never end up doing unless it was all stripped down, so its now or never really Chin.
Tom I did the radii by first trying to roll the bend in bending rolls but it was too thick for the rolls , so I just used them to clamp it and just pushed hard on the long side of the bend until it looked about right, the sheet was not tight to the roller but just bent in a nice curveBig Grin one of them rare times where you think .... Umm that worked out well Rotfl

Snailpowered , I cant say I have seen the film but do have an image of the thing you are on about ...... a kids film where allsorts of objects came alive I think ?
I got a bit of the electric panel done today but will post tomorrow when its in place .
Thanks again Mick.
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:


Messages In This Thread
Harrison L5 lathe rebuild - by Micktoon - 09-03-2012, 03:59 PM
RE: Harrison L5 lathe rebuild - by DaveH - 09-03-2012, 04:22 PM
RE: Harrison L5 lathe rebuild - by EdK - 09-03-2012, 05:04 PM
RE: Harrison L5 lathe rebuild - by stevec - 09-03-2012, 06:29 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 09-04-2012, 07:56 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 09-04-2012, 05:29 PM
RE: Harrison L5 lathe rebuild - by TomG - 09-04-2012, 08:19 PM
RE: Harrison L5 lathe rebuild - by SnailPowered - 09-04-2012, 10:04 PM
RE: Harrison L5 lathe rebuild - by stevec - 09-05-2012, 06:55 AM
RE: Harrison L5 lathe rebuild - by TomG - 09-05-2012, 07:28 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 09-23-2012, 03:26 PM
RE: Harrison L5 lathe rebuild - by DaveH - 09-23-2012, 05:52 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 09-24-2012, 03:31 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 09-24-2012, 03:49 PM
RE: Harrison L5 lathe rebuild - by DaveH - 09-24-2012, 03:50 PM
RE: Harrison L5 lathe rebuild - by EdK - 09-24-2012, 03:52 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 09-25-2012, 04:35 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 09-25-2012, 04:38 PM
RE: Harrison L5 lathe rebuild - by f350ca - 09-25-2012, 05:04 PM
RE: Harrison L5 lathe rebuild - by TOM REED - 09-25-2012, 05:05 PM
RE: Harrison L5 lathe rebuild - by stevec - 09-25-2012, 05:49 PM
RE: Harrison L5 lathe rebuild - by TomG - 09-25-2012, 05:57 PM
RE: Harrison L5 lathe rebuild - by EdK - 09-25-2012, 05:50 PM
RE: Harrison L5 lathe rebuild - by TomG - 09-25-2012, 05:52 PM
RE: Harrison L5 lathe rebuild - by stevec - 09-25-2012, 05:52 PM
RE: Harrison L5 lathe rebuild - by EdK - 09-25-2012, 06:05 PM
RE: Harrison L5 lathe rebuild - by stevec - 09-25-2012, 06:01 PM
RE: Harrison L5 lathe rebuild - by stevec - 09-25-2012, 07:06 PM
RE: Harrison L5 lathe rebuild - by DaveH - 09-25-2012, 07:11 PM
RE: Harrison L5 lathe rebuild - by sasquatch - 09-25-2012, 07:23 PM
RE: Harrison L5 lathe rebuild - by SnailPowered - 09-25-2012, 11:40 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 09-26-2012, 04:35 PM
RE: Harrison L5 lathe rebuild - by SnailPowered - 09-26-2012, 10:27 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 09-27-2012, 03:41 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 09-27-2012, 04:35 PM
RE: Harrison L5 lathe rebuild - by stevec - 09-27-2012, 04:36 PM
RE: Harrison L5 lathe rebuild - by DaveH - 09-27-2012, 05:26 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 09-30-2012, 08:20 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 10-12-2012, 05:05 PM
RE: Harrison L5 lathe rebuild - by sasquatch - 10-12-2012, 10:17 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 11-20-2012, 07:03 PM
RE: Harrison L5 lathe rebuild - by sasquatch - 11-20-2012, 09:44 PM
RE: Harrison L5 lathe rebuild - by stevec - 11-21-2012, 07:30 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 11-21-2012, 08:59 AM
RE: Harrison L5 lathe rebuild - by stevec - 11-21-2012, 06:20 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 11-21-2012, 04:24 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 11-21-2012, 04:36 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 11-21-2012, 05:12 PM
RE: Harrison L5 lathe rebuild - by DaveH - 11-21-2012, 05:27 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 11-22-2012, 05:29 PM
RE: Harrison L5 lathe rebuild - by sasquatch - 11-22-2012, 07:31 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 03-16-2013, 12:35 PM
RE: Harrison L5 lathe rebuild - by EdK - 03-16-2013, 02:57 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 03-16-2013, 05:26 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 03-16-2013, 06:10 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 03-18-2013, 05:06 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 03-18-2013, 05:12 PM
RE: Harrison L5 lathe rebuild - by DaveH - 03-18-2013, 05:33 PM
RE: Harrison L5 lathe rebuild - by Bill Gruby - 03-18-2013, 05:54 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-03-2013, 05:49 PM
RE: Harrison L5 lathe rebuild - by EdK - 05-03-2013, 06:13 PM
RE: Harrison L5 lathe rebuild - by sasquatch - 05-03-2013, 06:25 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 05-03-2013, 07:30 PM
RE: Harrison L5 lathe rebuild - by krv3000 - 05-06-2013, 10:10 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-06-2013, 04:18 PM
RE: Harrison L5 lathe rebuild - by Brian - 05-07-2013, 12:40 AM
RE: Harrison L5 lathe rebuild - by Dave J - 05-07-2013, 04:04 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-07-2013, 05:29 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-31-2013, 03:57 PM
RE: Harrison L5 lathe rebuild - by EdK - 05-31-2013, 04:01 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 05-31-2013, 04:24 PM
RE: Harrison L5 lathe rebuild - by TomG - 05-31-2013, 05:03 PM
RE: Harrison L5 lathe rebuild - by krv3000 - 05-31-2013, 05:27 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-31-2013, 05:37 PM
RE: Harrison L5 lathe rebuild - by stevec - 05-31-2013, 06:23 PM
RE: Harrison L5 lathe rebuild - by sasquatch - 05-31-2013, 06:48 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 05-31-2013, 08:03 PM
RE: Harrison L5 lathe rebuild - by f350ca - 05-31-2013, 08:33 PM
RE: Harrison L5 lathe rebuild - by DaveH - 06-01-2013, 11:47 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 01-29-2014, 06:30 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 01-29-2014, 06:37 PM
RE: Harrison L5 lathe rebuild - by TomG - 01-29-2014, 06:42 PM
RE: Harrison L5 lathe rebuild - by EdK - 01-29-2014, 06:54 PM
RE: Harrison L5 lathe rebuild - by PixMan - 01-29-2014, 07:48 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 01-30-2014, 05:31 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 01-30-2014, 07:01 PM
RE: Harrison L5 lathe rebuild - by EdK - 01-30-2014, 07:38 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 01-31-2014, 07:39 AM
RE: Harrison L5 lathe rebuild - by stevec - 01-31-2014, 07:55 AM
RE: Harrison L5 lathe rebuild - by f350ca - 01-31-2014, 08:55 AM
RE: Harrison L5 lathe rebuild - by DaveH - 01-31-2014, 01:05 PM
RE: Harrison L5 lathe rebuild - by krv3000 - 01-31-2014, 04:25 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-03-2014, 09:14 AM
RE: Harrison L5 lathe rebuild - by EdK - 02-03-2014, 12:41 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 02-03-2014, 01:20 PM
RE: Harrison L5 lathe rebuild - by krv3000 - 02-03-2014, 02:58 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-03-2014, 04:33 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 02-03-2014, 04:41 PM
RE: Harrison L5 lathe rebuild - by EdK - 02-03-2014, 05:14 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-03-2014, 05:24 PM
RE: Harrison L5 lathe rebuild - by TomG - 02-03-2014, 07:27 PM
RE: Harrison L5 lathe rebuild - by stevec - 02-04-2014, 07:48 AM
RE: Harrison L5 lathe rebuild - by Mayhem - 02-04-2014, 08:11 AM
RE: Harrison L5 lathe rebuild - by EdK - 02-04-2014, 04:29 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-04-2014, 06:47 PM
RE: Harrison L5 lathe rebuild - by EdK - 02-04-2014, 06:49 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 02-04-2014, 06:57 PM
RE: Harrison L5 lathe rebuild - by PixMan - 02-04-2014, 10:43 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 02-05-2014, 07:06 AM
RE: Harrison L5 lathe rebuild - by awemawson - 02-05-2014, 07:59 AM
RE: Harrison L5 lathe rebuild - by mfletch - 02-05-2014, 02:33 PM
RE: Harrison L5 lathe rebuild - by dallen - 02-05-2014, 03:25 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-06-2014, 06:36 PM
RE: Harrison L5 lathe rebuild - by stevec - 02-07-2014, 07:14 AM
RE: Harrison L5 lathe rebuild - by TomG - 02-07-2014, 09:35 PM
RE: Harrison L5 lathe rebuild - by big job - 02-08-2014, 04:53 AM
RE: Harrison L5 lathe rebuild - by Mayhem - 02-08-2014, 10:47 AM
RE: Harrison L5 lathe rebuild - by DaveH - 02-09-2014, 12:47 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-23-2014, 06:15 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 02-24-2014, 06:25 AM
RE: Harrison L5 lathe rebuild - by EdK - 02-24-2014, 08:43 AM
RE: Harrison L5 lathe rebuild - by krv3000 - 02-24-2014, 03:52 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-26-2014, 06:52 PM
RE: Harrison L5 lathe rebuild - by f350ca - 02-26-2014, 08:18 PM
RE: Harrison L5 lathe rebuild - by TomG - 02-26-2014, 08:37 PM
RE: Harrison L5 lathe rebuild - by tekfab - 02-27-2014, 12:16 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 02-27-2014, 05:27 AM
RE: Harrison L5 lathe rebuild - by EdK - 02-27-2014, 06:23 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-27-2014, 05:33 PM
RE: Harrison L5 lathe rebuild - by krv3000 - 02-27-2014, 05:59 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 02-27-2014, 06:10 PM
RE: Harrison L5 lathe rebuild - by TomG - 02-28-2014, 05:54 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-01-2014, 06:35 PM
RE: Harrison L5 lathe rebuild - by TomG - 05-01-2014, 07:16 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 05-01-2014, 08:20 PM
RE: Harrison L5 lathe rebuild - by dallen - 05-01-2014, 11:40 PM
RE: Harrison L5 lathe rebuild - by EdK - 05-02-2014, 05:31 AM
RE: Harrison L5 lathe rebuild - by stevec - 05-02-2014, 05:53 AM
RE: Harrison L5 lathe rebuild - by stevec - 05-03-2014, 06:31 AM
RE: Harrison L5 lathe rebuild - by haroldmulder - 05-02-2014, 08:17 AM
RE: Harrison L5 lathe rebuild - by doubleboost - 05-02-2014, 04:16 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-02-2014, 05:09 PM
RE: Harrison L5 lathe rebuild - by krv3000 - 05-02-2014, 05:30 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-02-2014, 05:39 PM
RE: Harrison L5 lathe rebuild - by dallen - 05-02-2014, 07:20 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-04-2014, 10:48 AM
RE: Harrison L5 lathe rebuild - by stevec - 05-05-2014, 05:33 AM
RE: Harrison L5 lathe rebuild - by EdK - 05-05-2014, 05:35 AM
RE: Harrison L5 lathe rebuild - by Mayhem - 05-05-2014, 06:45 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-19-2014, 05:19 PM
RE: Harrison L5 lathe rebuild - by EdK - 05-19-2014, 05:35 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-19-2014, 05:40 PM
RE: Harrison L5 lathe rebuild - by doubleboost - 05-19-2014, 05:53 PM
RE: Harrison L5 lathe rebuild - by krv3000 - 05-19-2014, 05:56 PM
RE: Harrison L5 lathe rebuild - by DaveH - 05-20-2014, 12:48 PM
RE: Harrison L5 lathe rebuild - by hermetic - 05-21-2014, 02:47 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-27-2014, 06:03 PM
RE: Harrison L5 lathe rebuild - by TomG - 05-27-2014, 06:45 PM
RE: Harrison L5 lathe rebuild - by tackit - 05-27-2014, 09:38 PM
RE: Harrison L5 lathe rebuild - by Shawn - 05-27-2014, 09:46 PM
RE: Harrison L5 lathe rebuild - by Mayhem - 05-28-2014, 07:44 AM
RE: Harrison L5 lathe rebuild - by DaveH - 05-28-2014, 09:38 AM
RE: Harrison L5 lathe rebuild - by krv3000 - 05-28-2014, 02:20 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-29-2014, 02:49 AM
RE: Harrison L5 lathe rebuild - by doubleboost - 05-29-2014, 03:08 PM
RE: Harrison L5 lathe rebuild - by Micktoon - 05-29-2014, 04:52 PM
RE: Harrison L5 lathe rebuild - by EdK - 05-29-2014, 04:58 PM
RE: Harrison L5 lathe rebuild - by stevec - 06-27-2014, 03:10 PM
RE: Harrison L5 lathe rebuild - by BillyT - 06-27-2014, 06:35 AM
RE: Harrison L5 lathe rebuild - by awemawson - 06-27-2014, 07:34 AM
RE: Harrison L5 lathe rebuild - by paul barrett - 08-09-2015, 05:40 AM
RE: Harrison L5 lathe rebuild - by paul barrett - 08-09-2015, 05:41 AM
RE: Harrison L5 lathe rebuild - by Mayhem - 08-09-2015, 05:49 AM
RE: Harrison L5 lathe rebuild - by paul barrett - 08-09-2015, 06:22 AM
RE: Harrison L5 lathe rebuild - by Micktoon - 08-11-2015, 03:22 AM



Users browsing this thread: 21 Guest(s)