MetalworkingFun Forum › Machining › General Metalworking Discussion v
Carbide Grinder

Thread Modes
Carbide Grinder
arvidj Offline
Junior
****
Posts: 736
Threads: 34
Joined: Feb 2012
Location: Minneapolis, MN
#8
09-18-2012, 09:25 PM
So what is the general consensus on the correct wheels to put on it? I had heard the diamond wheels from CDCO were the best bang for the buck if the goal tool sharpening.

Recommendations for material, grit and vendors welcome.
Reply
Thanks given by:


Messages In This Thread
Carbide Grinder - by TOM REED - 09-17-2012, 09:18 PM
RE: CARBIDE GRINDER - by f350ca - 09-17-2012, 09:43 PM
RE: CARBIDE GRINDER - by TOM REED - 09-18-2012, 08:59 AM
RE: Carbide Grinder - by Highpower - 09-18-2012, 09:50 AM
RE: Carbide Grinder - by arvidj - 09-18-2012, 09:52 AM
RE: Carbide Grinder - by EdK - 09-18-2012, 11:29 AM
RE: Carbide Grinder - by dallen - 09-18-2012, 11:56 AM
RE: Carbide Grinder - by arvidj - 09-18-2012, 09:25 PM
RE: Carbide Grinder - by EdK - 09-19-2012, 05:37 AM
RE: Carbide Grinder - by Tony Wells - 09-18-2012, 10:59 PM
RE: Carbide Grinder - by EdK - 09-19-2012, 05:43 AM
RE: Carbide Grinder - by TOM REED - 09-20-2012, 11:18 AM
RE: Carbide Grinder - by Highpower - 09-21-2012, 05:49 AM
RE: Carbide Grinder - by EdK - 09-21-2012, 06:18 AM
RE: Carbide Grinder - by EdK - 09-20-2012, 11:45 AM
RE: Carbide Grinder - by stevec - 09-20-2012, 01:58 PM
RE: Carbide Grinder - by TOM REED - 09-21-2012, 07:53 PM
RE: Carbide Grinder - by Highpower - 09-21-2012, 10:25 PM
RE: Carbide Grinder - by TOM REED - 09-25-2012, 01:51 PM
RE: Carbide Grinder - by stevec - 09-25-2012, 02:42 PM
RE: Carbide Grinder - by f350ca - 09-25-2012, 05:00 PM
RE: Carbide Grinder - by Mayhem - 09-30-2012, 09:59 AM
RE: Carbide Grinder - by Highpower - 09-30-2012, 10:31 PM
RE: Carbide Grinder - by TOM REED - 09-30-2012, 10:40 AM
RE: Carbide Grinder - by stevec - 09-30-2012, 11:39 AM
RE: Carbide Grinder - by Mayhem - 09-30-2012, 11:11 PM
RE: Carbide Grinder - by SnailPowered - 09-30-2012, 11:57 PM
RE: Carbide Grinder - by PixMan - 10-01-2012, 07:58 AM
RE: Carbide Grinder - by TOM REED - 10-13-2012, 07:35 PM
RE: Carbide Grinder - by Mayhem - 10-13-2012, 07:38 PM
RE: Carbide Grinder - by Highpower - 10-13-2012, 09:03 PM
RE: Carbide Grinder - by TOM REED - 10-13-2012, 09:08 PM
RE: Carbide Grinder - by f350ca - 10-13-2012, 09:17 PM
RE: Carbide Grinder - by TOM REED - 10-15-2012, 12:52 AM
RE: Carbide Grinder - by EdK - 10-15-2012, 09:28 AM
RE: Carbide Grinder - by TOM REED - 10-15-2012, 02:11 PM
RE: Carbide Grinder - by EdK - 10-15-2012, 02:25 PM
RE: Carbide Grinder - by TOM REED - 10-15-2012, 03:08 PM
RE: Carbide Grinder - by DaveH - 10-15-2012, 03:18 PM
RE: Carbide Grinder - by EdK - 10-15-2012, 03:21 PM
RE: Carbide Grinder - by stevec - 10-15-2012, 05:20 PM
RE: Carbide Grinder - by f350ca - 10-15-2012, 05:30 PM
RE: Carbide Grinder - by TOM REED - 10-15-2012, 07:05 PM



Users browsing this thread: 7 Guest(s)