626 Mill Z Axis Feed Nut

Hello There, Guest! Register

Thread Modes

626 Mill Z Axis Feed Nut

stevec Offline

Offline

69 yr. old senior

Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada

#12

09-16-2012, 06:41 PM

Ed, I'm pretty sure it's from back in the "pre-HSS" era.
Not that I am --choke cough!

Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.

Reply

« Next Oldest | Next Newest »

Messages In This Thread

626 Mill Z Axis Feed Nut - by doubleboost - 09-16-2012, 03:06 PM

RE: 626 Mill Z Axis Feed Nut - by stevec - 09-16-2012, 03:12 PM

RE: 626 Mill Z Axis Feed Nut - by DaveH - 09-16-2012, 03:19 PM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 09-16-2012, 03:25 PM

RE: 626 Mill Z Axis Feed Nut - by EdK - 09-16-2012, 03:31 PM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 09-16-2012, 03:38 PM

RE: 626 Mill Z Axis Feed Nut - by EdK - 09-16-2012, 03:51 PM

RE: 626 Mill Z Axis Feed Nut - by Micktoon - 09-16-2012, 03:51 PM

RE: 626 Mill Z Axis Feed Nut - by stevec - 09-16-2012, 04:06 PM

RE: 626 Mill Z Axis Feed Nut - by EdK - 09-16-2012, 05:04 PM

RE: 626 Mill Z Axis Feed Nut - by krv3000 - 09-16-2012, 04:57 PM

RE: 626 Mill Z Axis Feed Nut - by stevec - 09-16-2012, 06:41 PM

RE: 626 Mill Z Axis Feed Nut - by f350ca - 09-16-2012, 07:03 PM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 09-18-2012, 10:34 AM

RE: 626 Mill Z Axis Feed Nut - by Mayhem - 09-16-2012, 07:27 PM

RE: 626 Mill Z Axis Feed Nut - by DanH - 09-17-2012, 06:50 PM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 09-18-2012, 10:41 AM

RE: 626 Mill Z Axis Feed Nut - by Highpower - 09-18-2012, 07:15 AM

RE: 626 Mill Z Axis Feed Nut - by PixMan - 09-30-2012, 07:21 PM

RE: 626 Mill Z Axis Feed Nut - by sasquatch - 09-30-2012, 09:13 PM

RE: 626 Mill Z Axis Feed Nut - by Arbalest - 10-01-2012, 02:19 AM

RE: 626 Mill Z Axis Feed Nut - by krv3000 - 10-01-2012, 04:31 PM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 10-01-2012, 04:48 PM

RE: 626 Mill Z Axis Feed Nut - by stevec - 10-02-2012, 07:22 AM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 10-03-2012, 03:44 AM

RE: 626 Mill Z Axis Feed Nut - by Arbalest - 10-02-2012, 07:29 AM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 10-03-2012, 03:40 AM

RE: 626 Mill Z Axis Feed Nut - by stevec - 10-03-2012, 07:26 AM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 10-03-2012, 08:29 AM

RE: 626 Mill Z Axis Feed Nut - by stevec - 10-03-2012, 09:43 AM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 10-03-2012, 10:30 AM

RE: 626 Mill Z Axis Feed Nut - by doubleboost - 10-03-2012, 04:26 PM

RE: 626 Mill Z Axis Feed Nut - by Arbalest - 10-13-2012, 06:26 AM

Users browsing this thread: 14 Guest(s)