MetalworkingFun Forum › Machining › Welding & Casting v
Mill Engine Cylinder Casting

Thread Modes
Mill Engine Cylinder Casting
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#29
09-15-2012, 01:18 PM
sorry about the Z Axis nut, was just wondering hadn't seen anything posted for a while on it and I really want to see this engine finished, I hope to do a steam engine one day. I want one that I can actually use.

As far as casting goes I fired my furnace up today after about 4 months of the state being under a burn ban, sorry no video. poured a new rammer that I think is going to be way too heavy.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:


Messages In This Thread
Mill Engine Cylinder Casting - by doubleboost - 08-12-2012, 02:49 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-12-2012, 03:48 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-12-2012, 03:51 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-12-2012, 04:10 PM
RE: Mill Engine Cylinder Casting - by Mayhem - 08-12-2012, 11:45 PM
RE: Mill Engine Cylinder Casting - by krv3000 - 08-13-2012, 01:48 AM
RE: Mill Engine Cylinder Casting - by Highpower - 08-13-2012, 07:16 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 10:54 AM
RE: Mill Engine Cylinder Casting - by Highpower - 08-13-2012, 03:59 PM
RE: Mill Engine Cylinder Casting - by TomG - 08-13-2012, 07:19 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 04:03 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-13-2012, 04:38 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-13-2012, 04:45 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-14-2012, 03:45 PM
RE: Mill Engine Cylinder Casting - by EdK - 08-14-2012, 04:09 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-14-2012, 04:21 PM
RE: Mill Engine Cylinder Casting - by ETC57 - 08-14-2012, 09:17 PM
RE: Mill Engine Cylinder Casting - by f350ca - 08-14-2012, 09:26 PM
RE: Mill Engine Cylinder Casting - by doubleboost - 08-20-2012, 04:57 PM
RE: Mill Engine Cylinder Casting - by DaveH - 08-20-2012, 05:15 PM
RE: Mill Engine Cylinder Casting - by TomG - 08-20-2012, 06:11 PM
RE: Mill Engine Cylinder Casting - by Mayhem - 08-21-2012, 07:19 AM
RE: Mill Engine Cylinder Casting - by TomG - 08-21-2012, 01:15 PM
RE: Mill Engine Cylinder Casting - by dallen - 09-15-2012, 08:18 AM
RE: Mill Engine Cylinder Casting - by doubleboost - 09-15-2012, 11:17 AM
RE: Mill Engine Cylinder Casting - by DaveH - 09-15-2012, 01:04 PM
RE: Mill Engine Cylinder Casting - by dallen - 09-15-2012, 01:18 PM



Users browsing this thread: 5 Guest(s)