|
CNCing my mini mill
|
09-14-2012, 08:47 PM
right now I have a cheap unipolar driver hooked up to Mach3 I can get the motor to move but it doesn't have any power, and I know its big enough its a 485 Oz In motor, it should jerk hard enough to unscrew the thread on the acme nut screwed into the timing cog (brass part)
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough! 
|
|
« Next Oldest | Next Newest »
|
| Messages In This Thread |
|
CNCing my mini mill - by dallen - 08-03-2012, 08:45 AM
RE: CNCing my mini mill - by dallen - 08-05-2012, 10:16 AM
RE: CNCing my mini mill - by DaveH - 08-05-2012, 12:21 PM
RE: CNCing my mini mill - by dallen - 08-05-2012, 06:09 PM
RE: CNCing my mini mill - by dallen - 08-06-2012, 04:35 PM
RE: CNCing my mini mill - by Mayhem - 08-07-2012, 07:20 AM
RE: CNCing my mini mill - by dallen - 08-09-2012, 10:00 PM
RE: CNCing my mini mill - by dallen - 08-16-2012, 06:13 PM
RE: CNCing my mini mill - by dallen - 08-18-2012, 07:55 PM
RE: CNCing my mini mill - by DaveH - 08-19-2012, 05:06 PM
RE: CNCing my mini mill - by dallen - 08-19-2012, 07:13 PM
RE: CNCing my mini mill - by dallen - 08-26-2012, 08:37 AM
RE: CNCing my mini mill - by pamrick - 08-26-2012, 12:02 PM
RE: CNCing my mini mill - by dallen - 08-27-2012, 07:37 AM
RE: CNCing my mini mill - by DaveH - 08-27-2012, 01:42 PM
RE: CNCing my mini mill - by pamrick - 08-27-2012, 09:10 PM
RE: CNCing my mini mill - by SnailPowered - 08-28-2012, 12:14 AM
RE: CNCing my mini mill - by dallen - 08-28-2012, 08:35 AM
RE: CNCing my mini mill - by dallen - 09-01-2012, 03:53 PM
RE: CNCing my mini mill - by dallen - 09-04-2012, 10:05 PM
RE: CNCing my mini mill - by SnailPowered - 09-04-2012, 10:17 PM
RE: CNCing my mini mill - by dallen - 09-04-2012, 10:42 PM
RE: CNCing my mini mill - by SnailPowered - 09-04-2012, 11:41 PM
RE: CNCing my mini mill - by dallen - 09-07-2012, 07:31 AM
RE: CNCing my mini mill - by dallen - 09-14-2012, 06:39 PM
RE: CNCing my mini mill - by EdK - 09-14-2012, 07:36 PM
RE: CNCing my mini mill - by dallen - 09-14-2012, 08:25 PM
RE: CNCing my mini mill - by EdK - 09-14-2012, 08:32 PM
RE: CNCing my mini mill - by dallen - 09-14-2012, 08:47 PM
RE: CNCing my mini mill - by EdK - 09-14-2012, 08:56 PM
RE: CNCing my mini mill - by dallen - 09-15-2012, 09:24 AM
RE: CNCing my mini mill - by Rickabilly - 09-17-2012, 08:04 AM
RE: CNCing my mini mill - by dallen - 04-16-2013, 12:10 AM
RE: CNCing my mini mill - by dallen - 04-17-2013, 07:38 AM
RE: CNCing my mini mill - by dallen - 06-08-2013, 11:11 AM
RE: CNCing my mini mill - by EdK - 06-08-2013, 12:47 PM
RE: CNCing my mini mill - by dallen - 06-08-2013, 12:52 PM
RE: CNCing my mini mill - by EdK - 06-08-2013, 12:55 PM
RE: CNCing my mini mill - by dallen - 06-08-2013, 06:09 PM
RE: CNCing my mini mill - by DaveH - 06-10-2013, 02:52 PM
RE: CNCing my mini mill - by dallen - 06-16-2013, 02:21 PM
|
