Running a shaper - the compound

Thread Modes

Running a shaper - the compound

Sunset Machine Offline

Junior

Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA

#22

09-08-2012, 09:42 PM (This post was last modified: 09-08-2012, 09:44 PM by Sunset Machine.)

Wait .. the deal's off. Would you guys believe that the clapper was clapping too hard? Seems so, anyway. Snugged the clapper locks up and then loosened 'em a bit. The clapper is limited to about 1/4" swing and things are looking stable...

Like Post

« Next Oldest | Next Newest »

Messages In This Thread

Running a shaper - the compound - by Sunset Machine - 09-04-2012, 08:03 AM

RE: Running a shaper - the compound - by Mayhem - 09-04-2012, 08:35 AM

RE: Running a shaper - the compound - by dallen - 09-04-2012, 08:48 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-04-2012, 08:52 AM

RE: Running a shaper - the compound - by f350ca - 09-04-2012, 09:27 AM

RE: Running a shaper - the compound - by ScrapMetal - 09-04-2012, 03:08 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-05-2012, 08:26 AM

RE: Running a shaper - the compound - by big job - 09-06-2012, 05:24 AM

RE: Running a shaper - the compound - by stevec - 09-06-2012, 06:38 AM

RE: Running a shaper - the compound - by big job - 09-07-2012, 05:03 AM

RE: Running a shaper - the compound - by stevec - 09-07-2012, 06:52 AM

RE: Running a shaper - the compound - by big job - 09-07-2012, 05:17 AM

RE: Running a shaper - the compound - by EdK - 09-07-2012, 05:33 AM

RE: Running a shaper - the compound - by big job - 09-07-2012, 06:29 AM

RE: Running a shaper - the compound - by stevec - 09-07-2012, 07:11 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-07-2012, 08:04 AM

RE: Running a shaper - the compound - by big job - 09-08-2012, 05:05 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-08-2012, 09:28 AM

RE: Running a shaper - the compound - by aametalmaster - 09-08-2012, 10:59 AM

RE: Running a shaper - the compound - by f350ca - 09-08-2012, 10:52 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-08-2012, 01:17 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-08-2012, 09:42 PM

RE: Running a shaper - the compound - by big job - 09-09-2012, 07:49 AM

RE: Running a shaper - the compound - by dallen - 09-09-2012, 08:50 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-09-2012, 08:48 AM

RE: Running a shaper - the compound - by f350ca - 09-09-2012, 10:44 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-09-2012, 07:53 PM

RE: Running a shaper - the compound - by f350ca - 09-09-2012, 09:45 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-10-2012, 09:33 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-11-2012, 08:12 AM

RE: Running a shaper - the compound - by SnailPowered - 09-11-2012, 11:16 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-11-2012, 07:08 PM

RE: Running a shaper - the compound - by SnailPowered - 09-11-2012, 08:29 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-12-2012, 09:00 AM

RE: Running a shaper - the compound - by f350ca - 09-11-2012, 10:37 PM

RE: Running a shaper - the compound - by EdK - 09-12-2012, 05:32 AM

RE: Running a shaper - the compound - by Mayhem - 09-12-2012, 05:54 AM

RE: Running a shaper - the compound - by big job - 09-14-2012, 05:57 AM

RE: Running a shaper - the compound - by NevadaBlue - 09-20-2012, 04:11 PM

RE: Running a shaper - the compound - by stevec - 09-20-2012, 05:01 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-20-2012, 08:33 PM

Users browsing this thread: 7 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me