Running a shaper - the compound

Thread Modes

Running a shaper - the compound

big job Offline

Sophmore

Posts: 51
Threads: 0
Joined: Jun 2012
Location: S.E. Mass

#10

09-07-2012, 05:03 AM

Untitled.jpg (Size: 30.7 KB / Downloads: 117) Bj, what's that in pic #2? A martini (shaken not stirred) holder?

Oh I forgot that pic thats where the die grinder goes into but I use an
end mill

big job, proud to be a member of MetalworkingFun since Jun 2012.

Like Post

« Next Oldest | Next Newest »

Messages In This Thread

Running a shaper - the compound - by Sunset Machine - 09-04-2012, 08:03 AM

RE: Running a shaper - the compound - by Mayhem - 09-04-2012, 08:35 AM

RE: Running a shaper - the compound - by dallen - 09-04-2012, 08:48 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-04-2012, 08:52 AM

RE: Running a shaper - the compound - by f350ca - 09-04-2012, 09:27 AM

RE: Running a shaper - the compound - by ScrapMetal - 09-04-2012, 03:08 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-05-2012, 08:26 AM

RE: Running a shaper - the compound - by big job - 09-06-2012, 05:24 AM

RE: Running a shaper - the compound - by stevec - 09-06-2012, 06:38 AM

RE: Running a shaper - the compound - by big job - 09-07-2012, 05:03 AM

RE: Running a shaper - the compound - by stevec - 09-07-2012, 06:52 AM

RE: Running a shaper - the compound - by big job - 09-07-2012, 05:17 AM

RE: Running a shaper - the compound - by EdK - 09-07-2012, 05:33 AM

RE: Running a shaper - the compound - by big job - 09-07-2012, 06:29 AM

RE: Running a shaper - the compound - by stevec - 09-07-2012, 07:11 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-07-2012, 08:04 AM

RE: Running a shaper - the compound - by big job - 09-08-2012, 05:05 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-08-2012, 09:28 AM

RE: Running a shaper - the compound - by aametalmaster - 09-08-2012, 10:59 AM

RE: Running a shaper - the compound - by f350ca - 09-08-2012, 10:52 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-08-2012, 01:17 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-08-2012, 09:42 PM

RE: Running a shaper - the compound - by big job - 09-09-2012, 07:49 AM

RE: Running a shaper - the compound - by dallen - 09-09-2012, 08:50 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-09-2012, 08:48 AM

RE: Running a shaper - the compound - by f350ca - 09-09-2012, 10:44 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-09-2012, 07:53 PM

RE: Running a shaper - the compound - by f350ca - 09-09-2012, 09:45 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-10-2012, 09:33 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-11-2012, 08:12 AM

RE: Running a shaper - the compound - by SnailPowered - 09-11-2012, 11:16 AM

RE: Running a shaper - the compound - by Sunset Machine - 09-11-2012, 07:08 PM

RE: Running a shaper - the compound - by SnailPowered - 09-11-2012, 08:29 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-12-2012, 09:00 AM

RE: Running a shaper - the compound - by f350ca - 09-11-2012, 10:37 PM

RE: Running a shaper - the compound - by EdK - 09-12-2012, 05:32 AM

RE: Running a shaper - the compound - by Mayhem - 09-12-2012, 05:54 AM

RE: Running a shaper - the compound - by big job - 09-14-2012, 05:57 AM

RE: Running a shaper - the compound - by NevadaBlue - 09-20-2012, 04:11 PM

RE: Running a shaper - the compound - by stevec - 09-20-2012, 05:01 PM

RE: Running a shaper - the compound - by Sunset Machine - 09-20-2012, 08:33 PM

Users browsing this thread: 4 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me