Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
The following 1 user Likes hermetic's post:
Vinny (01-11-2020)
Hi Guys, below is part 2 of my workshop rebuild, the interior of the "Chuch lane end", no video this week as I have been off with sinusitis, a thumping head and a stiff neck, but I am determined to go back next week, so it will probably snow!! like, subscribe and enjoy, any comments and questions welcome!
Phil
East Yorkshire
https://youtu.be/cGCxwq2BsLg
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
The following 1 user Likes hermetic's post:
EdK (01-17-2020)
Hi Guys, part 3 of the workshop rebuild series, actually in the workshop itself. Still quite intensive, but not as difficult or time consuming as the Church lane end. Enjoy, like, subscribe, and be amazed that I actually completed it without having a complete meltdown!!
https://www.youtube.com/watch?v=FeWVEVSKjgY
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
Back to video this week chaps, part 2 of the workshop tour, Beyond the sliding door! Like subscribe, and enjoy, comments and questions very welcomed!
Phil
https://youtu.be/jebnxWfQdHY
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
Hi Chaps, having mainly recovered from my Lurgi, I am back at work on "light duties" so in the last couple of days, I have been building the new straight flue to try and cure the forge smoking problem. I have built a coupler/ hinge to join the new flue to the old one, and to install and maintain the flue extractor, and so that I can lower the flue in windy weather, as we do get a lot of wind in winter and early spring. There is also a slideshow of rebuilding and upgrading my BEN patents air compressor. Like, comment, subscribe if you want, but above all, Enjoy!!
Phil
East Yorkshire
https://youtu.be/TWi8wMpYLTA
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
Hi chaps, got the flue finished and put up this week, and also included my ride home over the Yorkshire wolds, like, subscribe, and enjoy!
Phil
East Yorkshire.
https://youtu.be/qkP69FMS0W4
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
The following 1 user Likes hermetic's post:
Vinny (02-14-2020)
Well here is an odd offering! have only been to the shop one day this week, as the weather has been very bad, and I am still a bit under it! Here is a job I did a few years ago on a Citroen 2cv, rebuilding the back end with new inner wings and boot floor. Beware of these cars! If you ever drive one, you will want one! They are so much fun, and dead easy to mend, but the downside is, they ROT! Not at all the car I would ever thought I would enjoy driving, just goes to show that performance isn't everything. Like comment subscribe, enjoy!
Phil
East Yorkshire
https://youtu.be/x6PVbn7_rho
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
The following 1 user Likes hermetic's post:
Vinny (02-21-2020)
Hi boys and girls, still not feeling quite right, but almost there! I did nothing this week, due to the storms and the wind howling round, so I have put together a slideshow of one of our late great engineering works, Doxford and Sons, of Sunderland, Marine engine builders. There is a link at the end to a silent colour amatuer film of the works in action. They built their last engine in 1980. Like, comment, subscribe, and as always, enjoy it!
Phil
Determined to get back to work next week cos i'm bored!
East Yorkshire
https://www.youtube.com/watch?v=_kWE95LEzQE
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
Hi Chaps, weather is still atrocious, bitter wind and horizontal sleet today, and I have stayed in the warm! here are some more of my projects, ongoing and finished, but we start out with the glory days of Dean Smith and Grace in Keighley, West Yorkshire, A factory I actually went to in the seventies when I got my first lathe, a DS&G 13Z. If you go to http://www.lathes.co.uk/dsg there is a factory tour there which is every bit as interesting as the Doxford one Hope you like it, and don't forget to comment and subscribe.
Phil
East Yorkshire
https://youtu.be/usA7r5qBmO0
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
Hi Chaps, the week was going so well, once it had started (Tuesday), weather has improved and I feel fit again, and it was all downhill fom there! When everything around you is going bad, you have to take the opportunity to "break on through to the other side" so it's head down, and puuuuuush!Like, laugh, subscribe, comment enjoy!
Phil,
East Yorkshire.
https://youtu.be/RFnsJj07X5k
Posts: 332
Threads: 10
Joined: Nov 2012
Location: East Yorkshire
The following 2 users Like hermetic's post:
Vinny (03-14-2020), JScott (08-24-2024)
Hi All, the welder part is on back order, and this week we decided, seing as the weather was good, to deal with some trees damaged in the recent winds, sort of commando gardening!. We have a 4 Acre field just across the village from the Workshop, and this week, and next week, if dry, will be a maintenance blitz, as it is next to the road, and fallen trees tend to interfere with traffic! please like, comment and subscribe!
Phil
Far East ( of Yorkshire)
https://youtu.be/mzDeuOelYwI
|
