MetalworkingFun Forum › Machining › Projects v
5 Cylinder Radial

Thread Modes
5 Cylinder Radial
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#221
06-18-2019, 08:05 AM
Very Nice, Brian. Thumbsup 

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,463
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#222
06-18-2019, 12:36 PM
Incredible job as always Brian. Smiley-eatdrink004

I found this after watching your last video. Different design but clearly shows the complexity of a radial engine. I love how he uses the internals of a Briggs & Stratton engine for comparison.

https://www.youtube.com/watch?v=qjnQKXNPsk4
Willie
Reply
Thanks given by:
Brian Offline
Junior
****
Posts: 437
Threads: 24
Joined: Sep 2012
Location: Sicily
The following 10 users Like Brian's post:
rleete (09-13-2019), JScott (09-13-2019), TomG (09-13-2019), Highpower (09-13-2019), arvidj (09-13-2019), Vinny (09-13-2019), EdK (09-13-2019), ScrapMetal (09-13-2019), Hawkeye (09-13-2019), Pete O (09-14-2019)
#223
09-13-2019, 03:22 AM
(06-18-2019, 12:36 PM)Highpower Wrote: Incredible job as always Brian.   Smiley-eatdrink004

I found this after watching your last video. Different design but clearly shows the complexity of a radial engine. I love how he uses the internals of a Briggs & Stratton engine for comparison.

https://www.youtube.com/watch?v=qjnQKXNPsk4

With the crank tail shaft made I can now fit the Master rod for a trial.  all looks good. 

   

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
Belugawhaleman Offline
Freshman
**
Posts: 1
Threads: 0
Joined: Sep 2019
Location: Gurnee, IL
#224
09-15-2019, 04:24 PM
Just finished going through this thread........Very impressive.
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,463
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#225
09-15-2019, 06:54 PM
(09-15-2019, 04:24 PM)Belugawhaleman Wrote: Just finished going through this thread........Very impressive.

Welcome to the forum. Smiley-signs046
Willie
Reply
Thanks given by:
Vinny Online
Another Whipping Boy
*******
Posts: 2,620
Threads: 100
Joined: Dec 2014
Location: Michigan
#226
09-15-2019, 07:20 PM
Welcome to the forum Beluga!
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
Brian Offline
Junior
****
Posts: 437
Threads: 24
Joined: Sep 2012
Location: Sicily
The following 8 users Like Brian's post:
f350ca (10-18-2019), EdK (10-18-2019), Highpower (10-18-2019), ScrapMetal (10-18-2019), Pete O (10-18-2019), Hawkeye (10-19-2019), Vinny (10-20-2019), arvidj (10-30-2019)
#227
10-18-2019, 05:40 AM
Hi Lads .Just a line to let you know that the material for the   front end case -- crank and oil pump has arrived and work is under way.
   

Brian.
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
Brian Offline
Junior
****
Posts: 437
Threads: 24
Joined: Sep 2012
Location: Sicily
The following 7 users Like Brian's post:
EdK (10-30-2019), arvidj (10-30-2019), f350ca (10-30-2019), TomG (10-30-2019), Pete O (10-30-2019), Highpower (10-30-2019), Vinny (11-01-2019)
#228
10-30-2019, 09:13 AM
Hi All
The forward bulkhead is nearly done it holds the inner crankshaft bearing and the annular inlet manifold.

This now leaves only the nose piece that holds the outer crank bearing to do, then the main casing is done, apart from fixing holes and O ring 
grooves ETC.

Brian.
   

   
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
#229
10-30-2019, 03:39 PM
How large of a plane will you build to house this engine?
Reply
Thanks given by:
Brian Offline
Junior
****
Posts: 437
Threads: 24
Joined: Sep 2012
Location: Sicily
The following 1 user Likes Brian's post:
f350ca (10-31-2019)
#230
10-31-2019, 10:45 AM
      

Hi Dr Stan 
If it ever gets to the stage of flying it. I want a very stable low speed aircraft with the capability of carrying a heavy load.. So my thoughts
are of a scale Spirit of St Louis.  With a span of 11 Ft    It's slab sided and parallel cord so it should be an easy build in foam sheet.
But all this is a long way ahead first lets just see if it runs???
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:




Users browsing this thread: 2 Guest(s)