MetalworkingFun Forum › Machining › Projects v
5 Cylinder Radial

Thread Modes
5 Cylinder Radial
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#181
10-29-2016, 03:46 PM
Fantastic work Brian Thumbsup  Looks amazing  Smiley-signs107 
Smiley-eatdrink004 
DaveH
 a child of the 60's and 50's and a bit of the 40's Smile
Reply
Thanks given by:
racer-john Offline
Freshman
**
Posts: 9
Threads: 0
Joined: Dec 2013
Location: Ontario, Canada
#182
11-20-2016, 12:55 PM
Beautiful workmanshift. Hope to hear it run soon.
racer-john, proud to be a member of MetalworkingFun Forum since Dec 2013.
Reply
Thanks given by:
Brian Offline
Junior
****
Posts: 437
Threads: 24
Joined: Sep 2012
Location: Sicily
The following 5 users Like Brian's post:
f350ca (01-12-2017), Mayhem (01-12-2017), Pete O (01-12-2017), EdK (01-12-2017), JScott (01-12-2017)
#183
01-12-2017, 02:50 PM
Have had a lot of bad weather over the past two months. six and a half inches of rain in 12 hours caused land slides in the town
and on the mountain roads and then snow. 
The shop was just to cold for me so I spent my time doing another slide show. you have seen most of it apart from the tapping part.  other than that I have been tucked up in the warm practising my ukulele.
 Still waiting to get a good gear cutter.

Brian Smiley-dancenana




Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
krv3000 Offline
Senior
*****
Posts: 1,520
Threads: 157
Joined: Feb 2012
Location: uk
#184
01-12-2017, 03:04 PM
Fantastic work Brian
krv3000, proud to be a member of MetalworkingFun Forum since Feb 2012.
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#185
01-12-2017, 06:07 PM
Hey Brian,

I was just wondering what you have been up to.

Thanks for sharing the slide show. It's definitely starting to look like a legitimate radial. Thumbsup

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
pepi Offline
Courious
****
Posts: 432
Threads: 27
Joined: Feb 2016
Location: Woodstock:GA
#186
01-13-2017, 08:08 AM
Brian,
I have a two descriptive words for that OUTRAGEOUS and RIGHTEOUS. That is an extreme build, feel very lucky for having the pleasure of seeing it come together.
Thank you
Greg
Magazines have issues, everything else has problems

Reply
Thanks given by:
Brian Offline
Junior
****
Posts: 437
Threads: 24
Joined: Sep 2012
Location: Sicily
The following 2 users Like Brian's post:
EdK (02-04-2017), f350ca (02-04-2017)
#187
02-04-2017, 12:17 PM
At last the replacement cutter has arrived. I have made a test piece so tomorrow I will make the test gear.
 Keep fingers crossed.

     

Brian   Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:
TomG Offline
Alt. Whipping Boy
*******
Posts: 3,798
Threads: 184
Joined: Jun 2012
Location: Farmington Hills, Michigan
#188
02-05-2017, 10:42 AM
Hopefully they took the time to mark this one correctly.  Slaphead

Tom
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
Bill Gruby Offline
Sophmore
***
Posts: 218
Threads: 9
Joined: Dec 2014
Location: Bristol Ct. USA
#189
02-05-2017, 03:27 PM
Many times people have bought from ebay only to find the sets, 1 thru 8 marked in reverse order.. The problem is ongoing with lots of complaints.

"Billy G"
Reply
Thanks given by:
Brian Offline
Junior
****
Posts: 437
Threads: 24
Joined: Sep 2012
Location: Sicily
#190
02-06-2017, 04:12 AM
This one is marked as  number 4  but 21- 25 tooth so what do we believe ??
Made a hash of the test yesterday  My fault something moved during the last cut
and I cant find what.  Very annoying, good job it was only the test piece.

Brian Smiley-dancenana
Brian, proud to be a member of MetalworkingFun since Sep 2012.
http://briansworkshop.weebly.com Welcome
Reply
Thanks given by:




Users browsing this thread: 32 Guest(s)