Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
The following 3 users Like aRM's post:
Mike E. (12-21-2016), f350ca (12-21-2016), Mayhem (12-21-2016)
Hi Guys
This must be getting boring for some of U.
Do regret that.
However, there's an interesting preamble to this we posted elsewhere.
Be that as it may, these are much smaller ones we fabricated from "Mystery Steel", which we thoroughly enjoyed working on.
All in the learning curve for us, if U may. 
The dimensions being different, we Threaded these to fine 1.0 mm Threads on the lathe, without any glitches, thankfully. The lathe behaved perfectly. In fact we did not like the fit of the first run at all and ran a second batch of the male parts which matched perfectly. And all that without using any Taps.
As for the Mystery Steel,it hardly required any polishing
And U can eyeball the results for Yourself
Thanks for "putting eyes" like thems would say.
aRM
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
Keep posting aRM - so few of us are actually making anything at the moment, so keep these posts coming.
Hunting American dentists since 2015.
Posts: 124
Threads: 14
Joined: Jan 2016
Location: North Vancouver, Canada
The following 12 users Like Old Minger's post:
f350ca (12-22-2016), EdK (12-22-2016), Mayhem (12-22-2016), Hawkeye (12-22-2016), Vinny (12-22-2016), DaveH (12-23-2016), Mike E. (12-23-2016), Bigtrev (01-15-2017), aRM (02-10-2017), hattrick300 (03-01-2017), cae2100 (10-05-2018), jagwinn (09-21-2021)
Ok no laughing now, but I made my first shop tool yesterday. I'm actually not even sure it qualifies as a tool but I'll post it anyway.
I needed some small M4 set screws and as my lathe is still not working this was going to be hand tools only. So inspired by you lot I decided to make a tool for the job. It's basically a piece of 01 that I drilled and tapped for M4, then I cut a slot in it and then hardened it. So I run an M4 bolt up the tool and then use the slot as a guide for the hacksaw, wind it out to the length required and cut it off.
Ok you can all stop laughing now, but the fact is a year ago I would have jumped in the car and driven to the shops and bought these set screws, now I'm making them courtesy of the information and inspiration from this forum.
Cheers Fellas 
Posts: 340
Threads: 24
Joined: Aug 2014
Location: Seattle, WA
Nothing to laugh at, minger. You had a need, you figured out a solution, and you made it work. That's a gold medal in my book.
Mike
SB 10K (1976) Rockwell vertical mill (1967) Rockwell 17" drill press (1946) Me (1949)
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
I'd say quite professional, going the extra step to harden it.
Free advice is worth exactly what you payed for it.
Greg
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
(12-21-2016, 07:57 PM)Mayhem Wrote: Keep posting aRM - so few of us are actually making anything at the moment, so keep these posts coming.
Yes Sir
Hope to
May U enjoy Your festivities
Stay Safe
aRM
Posts: 214
Threads: 19
Joined: Oct 2014
Location: SOUTH AFRICA,KZN,DURBAN
Old Minger Wrote: Ok you can all stop laughing now, but the fact is a year ago I would have jumped in the car and driven to the shops and bought these set screws, now I'm making them courtesy of the information and inspiration from this forum.
Cheers Fellas
Hey, U not Ol' Minger, U one Young Minger with brilliant practical ideas that work
This was neat and cool. Ingenious, I'd say. 
And we not laughing either, 'cos we also can benefit and use that idea some day
So nothing to laugh at. Good show for showing and sharing, Man
Keep 'em rolling we will say.
aRM
Posts: 8,846
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
Nothing at all to laugh at Old Minger. Good job on finding a solution and ending up with a nice tool for your efforts.
Ed
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
Old Minger, nicely done 
DaveH
a child of the 60's and 50's and a bit of the 40's 
Posts: 535
Threads: 39
Joined: Jan 2013
Location: Kelowna, BC, Canada
The following 5 users Like Hawkeye's post:
Mayhem (12-24-2016), aRM (12-24-2016), f350ca (12-24-2016), EdK (12-24-2016), DaveH (12-24-2016)
I picked up a selection of adjustable reamers a few years ago. Some are quite large, so I needed a tap wrench that could accommodate the various sizes. I finally got around to it today. The end of the reamer is nearly 1 1/4" square.
A little light knurling to improve the grip.
Mike
If you can't get one, make one.
Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.
|
