MetalworkingFun Forum › Machining › Projects v
Todays Project - What did you do today?

Thread Modes
Todays Project - What did you do today?
Dr Stan Offline
Senior
*****
Posts: 2,328
Threads: 271
Joined: Jun 2014
Location: La Libertad, Philippines
The following 1 user Likes Dr Stan's post:
EdK (10-25-2016)
#4,341
10-24-2016, 10:32 PM
(10-24-2016, 07:48 PM)Vinny Wrote: I think he only stocks 24ct gold.

He only uses that when he's out of platinum.   Big Grin
Reply
Thanks given by:
the penguin Offline
Junior
****
Posts: 482
Threads: 89
Joined: Oct 2012
Location: camillus (syracuse), ny
#4,342
10-25-2016, 11:24 AM
Back in Rochester, starting up the new 900 hp boiler (36 million BTUs).  Sittin here watching a boiler run at 5%, for hours on end, is mind numbing, ranks right up there with watching grass grow or paint dry.

I asked for a plant tour and was turned down, apparently, they saw no use in it, as I'm not about to buy any machines.

The worse part of the job, is that it's only Tuesday, I can't go home until Friday.

I guess I'll go to YouTube and watch This Old Tony and Tom's videos.
jack
Reply
Thanks given by:
the penguin Offline
Junior
****
Posts: 482
Threads: 89
Joined: Oct 2012
Location: camillus (syracuse), ny
#4,343
10-25-2016, 01:43 PM (This post was last modified: 10-25-2016, 01:46 PM by the penguin.)
Move along, nothing to see here (apparently the iPad has a mind of its own).
jack
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#4,344
10-25-2016, 02:11 PM
drilled a 1.250 hole in some 2 inch thick steel


   
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Roadracer_Al Offline
Junior
****
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
#4,345
10-25-2016, 05:45 PM
Looks like a barrel vise.
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#4,346
10-25-2016, 06:42 PM
Looks good  Thumbsup   - one 'smart' vice Big Grin
Smiley-eatdrink004
DaveH
 a child of the 60's and 50's and a bit of the 40's Smile
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#4,347
10-25-2016, 08:38 PM (This post was last modified: 10-25-2016, 08:40 PM by dallen.)
yea I gotta open the hole up by 250 thousands for the bushings to fit, I've seen some made where people used 1/2 inch bolts in them I'm not taking chances of the bolts stretching I used 3/4 X 16 TPI I would rather sqeeze the bushings then have the barrel slip.

everyone that's messed with mauser actions knows how hard they can be to get apart when you have to pull the tube.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,861
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
The following 4 users Like EdK's post:
DaveH (10-29-2016), f350ca (10-29-2016), PixMan (10-29-2016), aRM (11-06-2016)
#4,348
10-29-2016, 02:53 PM
I finished off this part for the vise work stop.

Ed

   
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#4,349
10-29-2016, 03:58 PM
Nice job Ed, Thumbsup 
Smiley-eatdrink004 
DaveH
 a child of the 60's and 50's and a bit of the 40's Smile
Reply
Thanks given by: EdK
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#4,350
10-29-2016, 05:57 PM
Nice work Ed. Tell us what you used for the interrupted cut on the lathe. Did you hold the square stock in a 4-jaw chuck?
Reply
Thanks given by: EdK




Users browsing this thread: 38 Guest(s)