MetalworkingFun Forum › Machining › General Metalworking Discussion v
Peerless Shaper

Thread Modes
Peerless Shaper
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#61
10-15-2015, 08:24 PM
The down feed dial on this one is as hopeless as the Logan.
[Image: IMG_1929.jpg]

One revolution is .125 how are you supposed to read that while the ram is going back and forth?
Plan to make a new one somewhere around 3 inches in dia, a readable size. 
Can anyone see a reason not to make the dial out of aluminum? Would be much easier to engrave deep graduations that could be visible.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Vinny Online
Another Whipping Boy
*******
Posts: 2,620
Threads: 100
Joined: Dec 2014
Location: Michigan
The following 1 user Likes Vinny's post:
f350ca (10-15-2015)
#62
10-15-2015, 08:50 PM
That little bitty ring under the crank? How you supposed to read it when the ram is stopped? Anyway the only drawback I see to aluminum is it getting dinged up but I'd prolly still go with aluminum anyway.
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
big job Offline
Sophmore
***
Posts: 51
Threads: 0
Joined: Jun 2012
Location: S.E. Mass
#63
10-16-2015, 04:40 AM (This post was last modified: 10-16-2015, 04:45 AM by big job.)
(10-15-2015, 08:50 PM)Vinny Wrote: That little bitty ring under the crank?  How you supposed to read it when the ram is stopped?  Anyway the only drawback I see to aluminum is it getting dinged up but I'd prolly still go with aluminum anyway.

Thats simple I put a 6 inch DRO on mine with a remote readout
big job, proud to be a member of MetalworkingFun since Jun 2012.
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#64
10-16-2015, 06:51 AM
that's way there's a clutch   Big Grin Big Grin
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Sunset Machine Offline
Junior
****
Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA
#65
10-16-2015, 08:32 AM
The first time I ran my shaper I was looking for yellow chips and clapping noises. Everything was a blur. That's not how you run a shaper. You can't read the dial and the clapping pounds the compound down deeper into the work than you might want.. Setting the speed to where you can read the compound feed dial works a whole lot better. All of a sudden, you're its master.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
EdK (10-17-2015)
#66
10-17-2015, 08:40 PM
Decided to go with a steel dial, chemically blue it then polish off the surface hopefully leaving the lines blued.
Got the blank made, thats the original dial on top.
[Image: IMG_1932.jpg]

Tried to figure out the indexing head to cut the required 125 divisions. Works out that I need a 25 division plate, of course I don't have one, looked into compound indexing in the machinist handbook, decided it would be a whole lot easier to make a 50 decision plate using the 15 division one.

[Image: IMG_1930.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 4 users Like f350ca's post:
Mayhem (10-18-2015), arvidj (10-18-2015), EdK (10-18-2015), Highpower (10-20-2015)
#67
10-17-2015, 11:16 PM
The new plate worked.

[Image: IMG_1933.jpg]

Now to stamp the numbers.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#68
10-18-2015, 07:07 AM
Nice job (as always) Greg.

One option would be to use an oil-based paint and rub the paint into the division marks/numbers with a soft rag, wiping off the excess. That is what I did with the identification rings on the drawbars that I made.
Hunting American dentists since 2015.
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#69
10-18-2015, 07:43 AM
(10-17-2015, 11:16 PM)f350ca Wrote: The new plate worked.
Looks good as well Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Sunset Machine Offline
Junior
****
Posts: 716
Threads: 32
Joined: Apr 2012
Location: Washington, USA
#70
10-18-2015, 08:46 AM
Each division on mine represents .005", something I discovered the hard way.
I think it had an axe in the family tree.
Reply
Thanks given by:




Users browsing this thread: 5 Guest(s)