MetalworkingFun Forum › Machining › Projects v
Building an Aligator

Thread Modes
Building an Aligator
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 5 users Like f350ca's post:
EdK (10-02-2015), DaveH (10-02-2015), Hawkeye (10-02-2015), Mayhem (10-03-2015), PixMan (10-04-2015)
#71
10-02-2015, 08:02 PM
Set the main shaft in place today. The boiler is fastened down, but the engine is just sitting there for now.
[Image: IMG_1908.jpg]

Started framing the lower cabin.

[Image: IMG_1910.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 2 users Like f350ca's post:
EdK (10-06-2015), Mayhem (10-06-2015)
#72
10-06-2015, 05:28 PM
Made the rafters for the cabin today. Cut a 1 inch crown in them to shed water.
Dr Bill cut the logs and sawed the lumber for the cabin sides and roof. Not bad for 86.

[Image: IMG_1913.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Vinny Online
Another Whipping Boy
*******
Posts: 2,620
Threads: 100
Joined: Dec 2014
Location: Michigan
#73
10-06-2015, 07:20 PM
Where the shafts come out the sides.. Waterwheel drive?
Logan 200, Index 40H Mill, Boyer-Shultz 612 Surface Grinder, HF 4x6 Bandsaw, a shear with no name, ...
the nobucks boutique etsy shop  |  the nobucks boutique
Website
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
#74
10-06-2015, 09:58 PM
Yep, the paddle wheels slide onto those shafts. They will be 8 feet in dia, the blades 8 blades are 16 inch wide and 12 inches deep.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#75
10-07-2015, 07:00 AM
It must be gratifying to see that big long shaft you made in your shop sitting there, ready for action. It sure looks good!
Reply
Thanks given by: f350ca
Roadracer_Al Offline
Junior
****
Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
The following 1 user Likes Roadracer_Al's post:
f350ca (10-07-2015)
#76
10-07-2015, 08:50 PM
You fellas just can't get enough of building stuff, can you? I mean that in the best way possible. :)
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 1 user Likes dallen's post:
f350ca (10-07-2015)
#77
10-07-2015, 09:07 PM
Greg's probably going to use it to salvage 200 year old logs from the bottom of the lakes and rivers in the area so he can saw them up into lumber to use in his cabinet building.
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#78
10-08-2015, 06:21 AM
I thought he was going to come and visit me in it Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
EdK (10-08-2015)
#79
10-08-2015, 08:36 AM
I was planning it Darren, are you sure there's enough trees along the way to feed the boiler?
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 2 users Like f350ca's post:
Mayhem (05-24-2016), PixMan (06-08-2016)
#80
05-24-2016, 05:03 PM
Haven't posted this one in a while. 
Have the cabin roof on and some safety rails. 

[Image: IMG_2221.jpg]

Currently getting the main bearings ready to pour the babbit

[Image: IMG_2222.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 5 Guest(s)