Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
(09-19-2012, 05:59 PM)stevec Wrote: Oh jeez! another crutch, thank you.
heck I don't need a crutch I need the whole ambulance and crew at times
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough!
Posts: 537
Threads: 15
Joined: Jun 2012
Location: Cambridge, England
There are a few reasons for the clear lenses on both sides of the glass, there should be three clears in total, one on each side of the green glass and a third as a safety shield under the flip up lens, to guard against flying flux or scale when the lens is flipped up, so effectively to act as safety goggles or glasses when chipping slag, the lens on the front of green glass is to protect from spatter, and the clear lens on the back of the green lens protects the back of the green lens from spatter as well but primarily from impact as the green glass is very brittle and if the flipper is up and a large piece of flying debris from a grinder or a piece of large slag or chipping hammer fragment hits the lens from the back it will be easily broken.
Regards
Rick,
Laser eyes surgery, yes I'd definately give it a go if I was to end up with eyes that could shoot Laser beams, I mean how handy would that be?
Whatever it is, do it today, Tomorrow may not be an option and regret outlasts fatigue.
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
(09-19-2012, 05:34 PM)Highpower Wrote: They are available in many different diopters - sort of like the cheap reading glasses you find at the drug store. Most welding helmets have a recessed area behind (or in front of) the welding lens, underneath the protector sheet that the cheater fits into. So your "eyeglasses" are then a part of the welding helmet.
So I assume the cheater lenses are helmet specific and not a standard size where one fits all. Is that correct?
I'll have to check my helmet and see if it has the recess for the cheater lens.
Ed
Posts: 4,438
Threads: 183
Joined: Feb 2012
Location: Missouri, USA
I think the 2X4 lens is pretty much the standard for modern helmets.
Willie
Posts: 410
Threads: 77
Joined: Mar 2012
Location: Salem, Ohio
(04-21-2012, 07:07 AM)stevec Wrote: OK, live and learn, the increase from .025 to .030 is about 25% I wouldn't have thought it would make THAT much difference.
Guess I'll put a roll of .030 on my list for my next trip to town (in NS, the land of you can't get it here)
Its like stick electrodes going from 3/32 to 1/8, not much difference in size but a different beast when welding them...Bob
Bob Wright
Metal Master Fab
Salem Ohio
Birthplace of the Silver and Deming drill bit.
5 Lathes, SBL Shaper, Lewis Mill, 7 drill presses, 5 welders...
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
09-23-2012, 07:50 AM
(This post was last modified: 09-23-2012, 07:51 AM by stevec.)
(09-23-2012, 06:52 AM)aametalmaster Wrote: (04-21-2012, 07:07 AM)stevec Wrote: OK, live and learn, the increase from .025 to .030 is about 25% I wouldn't have thought it would make THAT much difference.
Guess I'll put a roll of .030 on my list for my next trip to town (in NS, the land of you can't get it here)
Its like stick electrodes going from 3/32 to 1/8, not much difference in size but a different beast when welding them...Bob
I agree about the sticks Bob. But I found fault with the math in the first quote. I believe the dummy meant 20% increase not 25%.
(Hey, I was/am that dummy! )
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
Bump. Welding cart is on the list for this summers projects.
Ed
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
The following 1 user Likes DaveH's post:
Mayhem (07-08-2015)
I don't think you have Summer where you live -
DaveH
Posts: 8,842
Threads: 318
Joined: Feb 2012
Location: Arizona/Minnesota
Hmmm, good point Dave.
Ed
Posts: 482
Threads: 89
Joined: Oct 2012
Location: camillus (syracuse), ny
(07-07-2015, 08:01 PM)EdK Wrote: Hmmm, good point Dave.
Ed
will it be done before the Lutefish celebration??
jack
|