Posts: 691
Threads: 14
Joined: Feb 2015
Location: Oakland, California
The following 3 users Like Roadracer_Al's post:
Mayhem (06-10-2015), DaveH (06-10-2015), EdK (06-10-2015)
A typical belt grinder has 3 wheels -- a drive wheel, which is typically crowned, a tension idler, which is usually where the tracking adjustment is located, and the contact wheel, which is where the work is done. Contact wheels are typically mounted on a loose tool arm so they can be removed & replaced easily. The diameter of the contact wheel controls the shape of the hollow grind on a blade. You can buy contact wheels in 6" up to about 14" diameters. Contact wheels are often urethane coated to extend the life of the abrasive belt, and make grinding quieter. They need to be absolutely cylindrical, and concentric/parallel to the axle of the wheel or a poor finish on the knife will result.
Flat plattens are used to create flat bevels. Many of the cheaper grinders use mild steel bar stock as the platten which wears quickly. Higher-end grinders use hardened tool steel. Some knife guys use fire-proof glass, or ceramic. One guy has even made a water-cooled platten backer to both extend the life of the belt and reduce the frequency of water baths on the blade. The plattens are always considered consumable.
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
(06-09-2015, 04:44 PM)RobWilson. Wrote: About the same time as when rubbing something back and forth on a bit sand paper became lapping .
I thought that was polishing?
Hunting American dentists since 2015.
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
Sanding / Grinding
Easy................ Sand Wood ................... Grind Metal
DaveH
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
(06-06-2015, 10:48 AM)dallen Wrote: Hope 3400 RPM motors are cheaper there then they are here.
Gosh David you're right ........... 3 phase motor do seem much cheaper here, however they are 2840rmp, and are 220v.
DaveH
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
A new company just started to make them.
Here it is ........................ now isn't that beautiful
DaveH
Posts: 8,863
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
Looks pretty much the same as all of the others. It might look better in pink though.
Ed
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
(06-10-2015, 04:30 PM)EdK Wrote: Looks pretty much the same as all of the others. It might look better in pink though.
Ed
Funny you should say that, I asked if I could have it in pink, he said "sure, will need a couple of extra days"
This is a two wheel belt grinder so the belt can be driven in reverse. (No idea why one would run it in reverse)
DaveH
Posts: 2,620
Threads: 100
Joined: Dec 2014
Location: Michigan
(06-10-2015, 05:02 PM)DaveH Wrote: This is a two wheel belt grinder so the belt can be driven in reverse. (No idea why one would run it in reverse)
DaveH
So you can sharpen both sides of the knife you're making.
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 3 users Like f350ca's post:
EdK (06-10-2015), DaveH (06-10-2015), stevec (06-11-2015)
To put the metal back on.
Free advice is worth exactly what you payed for it.
Greg
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
(06-10-2015, 01:07 PM)DaveH Wrote: (06-06-2015, 10:48 AM)dallen Wrote: Hope 3400 RPM motors are cheaper there then they are here.
Gosh David you're right ........... 3 phase motor do seem much cheaper here, however they are 2840rmp, and are 220v.
DaveH
I have a 1750 rpm motor on my belt grinder it works ok, but could use the extra speed.
But seeing as how its a 3 phase motor I could hook it up to one of the VFDs that I have and run it at 120 hz which would run the RPM up around 3400.
But for what I do with it I can afford to buy a new belt a little quicker then if I had the extra RPM.
I'm going to have to try Vinney's trick on making a soft rubber covered contact wheel, mines just bare aluminum that I cast and machined out it works is all I care about, that and the belt staying on
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.
If life seems normal, your not going fast enough! 
