MetalworkingFun Forum › Machining › Projects v
Todays Project - What did you do today?

Thread Modes
Todays Project - What did you do today?
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#2,901
02-22-2015, 11:48 AM
I concur with arvid regarding the state of the turbo seals.

Darren, are there any other bits of plastic on the engine that show signs of melting? Sensors or wiring connectors on the engine etc.?
From the looks of that idler I would bet that engine got HOT since the bearing is still free running. I would go over the cooling system with a fine tooth comb. Water pump, radiator, etc. And be sure to check the deck surface with a straight edge for warpage. Any traces between the cylinders and the cooling jacket ports deserve much scrutiny. I've seen engines that got hot enough to melt the timing belt covers too. Yikes
Smiley-gen163

   
Willie
Reply
Thanks given by: Mayhem
how'sitwork? Offline
Freshman
**
Posts: 16
Threads: 2
Joined: Jan 2015
Location: UK
#2,902
02-22-2015, 05:10 PM
Well

just got in from milling 2 tangential tool holders. interesting setting up for 12' in 2 dimensions. Now need to make a sharpening jig for the grinder and try it out!

Then decided to open out the slots on the "new" Boxford MD4 pillar drill table so I can use my existing hold down t nuts etc. Went well and didn't break a cutter today ( big improvement on last week when milling the slots for the tool bit in the holders- 2 cutters broken, both through over enthusiasm- live and learn).

Good luck with the car!
Reply
Thanks given by:
Shawn Offline
Junior
****
Posts: 313
Threads: 34
Joined: Nov 2013
Location: Kamloops, BC, Canada
The following 5 users Like Shawn's post:
Mayhem (02-23-2015), PixMan (02-23-2015), arvidj (02-23-2015), Highpower (02-23-2015), EdK (02-23-2015)
#2,903
02-23-2015, 01:57 AM
I was turning the spindle shaft for my countershaft project today and though I would try turning between centres (I know, I can't believe I have never tried this before either) anyways to cut a short story even shorter, I tweaked my tailstock a bit and was able to get slightly less than 1/2 thousand difference between ends. I though that was pretty darn impressive for a lathe that's been around for 60 years or so. 

[Image: image.jpg]
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by:
Bill Gruby Offline
Sophmore
***
Posts: 218
Threads: 9
Joined: Dec 2014
Location: Bristol Ct. USA
The following 1 user Likes Bill Gruby's post:
Shawn (02-23-2015)
#2,904
02-23-2015, 03:03 PM
Prints for the Die Filer are done. I will get them copied and off to Ed this week. There are 24 pages.

"Billy G"
Reply
Thanks given by: JScott
JScott Offline
Sophmore
***
Posts: 240
Threads: 30
Joined: Mar 2014
Location: Planeta Rica, Colombia
#2,905
02-23-2015, 04:29 PM
(02-23-2015, 03:03 PM)Bill Gruby Wrote: Prints for the Die Filer are done. I will get them copied and off to Ed this week. There are 24 pages.

"Billy G"

Is there a gamble going on if Ed can put them on CAD as fast or faster than Billy G put them on paper by hand?

Popcorn
JScott, proud to be a member of MetalworkingFun Forum since Mar 2014.
Reply
Thanks given by:
Bill Gruby Offline
Sophmore
***
Posts: 218
Threads: 9
Joined: Dec 2014
Location: Bristol Ct. USA
#2,906
02-23-2015, 04:55 PM (This post was last modified: 02-23-2015, 04:56 PM by Bill Gruby.)
HUH -- That was slow, not fast. I had to re-do some so that he could read them. They should have been done yesterday. Big Grin

"Billy G"
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
The following 1 user Likes dallen's post:
PixMan (02-25-2015)
#2,907
02-25-2015, 09:04 PM
been working on this the last couple of days, today was making the hammer which I filed the square hole one stroke of the file too big

[Image: hammer.jpg]

the back side

[Image: stolzer-lock.jpg]
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#2,908
02-26-2015, 09:00 AM
(02-25-2015, 09:04 PM)dallen Wrote: today was making the hammer which I filed the square hole one stroke of the file too big
Bash  who hasn't done that Smile
Looks nice David Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#2,909
02-26-2015, 10:20 AM
(02-26-2015, 09:00 AM)DaveH Wrote: Bash  who hasn't done that Smile
Looks nice David Thumbsup
Smiley-eatdrink004
DaveH

Thanks

takes some patience and a lot of practice with the filing to make one right, guess I need more practice.

DA 
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#2,910
02-26-2015, 11:03 AM
(02-26-2015, 10:20 AM)dallen Wrote: takes some patience and a lot of practice with the filing to make one right, guess I need more practice.

DA 

Nope, a little more patience Big Grin 
Smiley-eatdrink004
DaveH
Reply
Thanks given by:




Users browsing this thread: 94 Guest(s)