Todays Project - What did you do today?
Thanks Ed. This thing came along at just the right time for me. My old Jacobson Sno-Burst was a real work-out for me. I had to rebuild the diaphragm type carburetor just about every year because the ethanol in our fuel would eat up the diaphragms. Trying to get it started the first snow fall of the season was a major chore. Had to pull on that *@&#^&$!! recoil starter for half an hour while feeding the carb starting fluid long enough for the engine to give enough impulses to break the diaphragms loose so they would move again. Arrrrgggghhhh!  Rant

Luckily the Toro has a float type carburetor  Smiley-dancenana so that shouldn't be a problem anymore. It starts with the first pull of the rope. Still, when the temps really drop, (and with my bad shoulders) I will be very glad to have the electric starter and be able to just "plug and play".  Cool 
Willie
Reply
Thanks given by:
Nice job Willie,  Smiley-signs107   Thumbsup  never seen one in real life - don't suppose I ever will.

But they sure do look good fun to use.
Smiley-eatdrink004 
DaveH
Reply
Thanks given by: Highpower
(02-06-2015, 12:40 PM)DaveH Wrote: But they sure do look good fun to use.
Smiley-eatdrink004 
DaveH

Maybe when you're young....  Smiley-gen151
Willie
Reply
Thanks given by:
worked on this today, still have a few things to do to it.

[Image: putting%20it%20together.jpg]

And put in some hours on this project.
Photo's not the best need a wide angle to get a really good up close shot.
[Image: rifle-2_8_15.jpg]

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
I know what the thing on the bottom is, but what the heck is the thing on the top?
[Image: TomsTechLogo-Profile.png]
Reply
Thanks given by:
(02-08-2015, 09:26 PM)TomG Wrote: I know what the thing on the bottom is, but what the heck is the thing on the top?

someones version of a 72 inch belt grinder that I was given as a basket case, so I put it together. hope to fire it up tomorrow.

that thing on the bottom is a black hole that keeps on sucking in money Rotfl Rotfl

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Blued the Barrel yesterday, but think I'm going to go a couple more wipe and boil sessions with it, just because I can.

[Image: barrel-blued.jpg]
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Made some adapters and feet for a friends hexacopter (drone).

[Image: hex_landing_gear_2.jpg]

[Image: IMG_20150207_155139.jpg]

[Image: IMG_20150207_203405.jpg]
Steve S
Check out MyShopNotes on youtube.
Reply
Thanks given by:
David, do you use those 'bluing salts' ?
Smiley-eatdrink004 
DaveH
Reply
Thanks given by:
(02-14-2015, 12:51 PM)DaveH Wrote: David, do you use those 'bluing salts' ?
Smiley-eatdrink004 
DaveH

I wish, but they are way too much trouble to use inside the house. and I don't have a place outside to put the setup at. So its chemical solutions until I get rich and can afford a separate building to put them in.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:




Users browsing this thread: 5 Guest(s)