MetalworkingFun Forum › Machining › Projects v
Mule

Thread Modes
Mule
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#21
11-15-2014, 10:17 PM
What Willie said. Nice work Greg
Hunting American dentists since 2015.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 3 users Like f350ca's post:
stevec (11-18-2014), EdK (11-18-2014), Highpower (11-18-2014)
#22
11-18-2014, 12:41 AM
More progress on the frame. Im using (recycling) old tube I got a while back, think it was some form of racks or shelling. Its rusty but still has a certain amount of paint, took me an hour this morn to clean up 3, 6 foot lengths. If I valued my time it would probably be more cost effective to have bought new material.

[Image: IMG_1500.jpg]

[Image: IMG_1502.jpg]

[Image: IMG_1503.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
#23
11-18-2014, 05:48 AM
Looking good Greg.
Hunting American dentists since 2015.
Reply
Thanks given by:
dallen Offline
Senior
*****
Posts: 1,827
Threads: 51
Joined: Apr 2012
Location: Oklahoma
#24
11-18-2014, 08:19 AM
kids are going to have a blast when you get it finished
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Micktoon Offline
Junior
****
Posts: 638
Threads: 43
Joined: Sep 2012
Location: England
#25
11-18-2014, 06:04 PM
Looks like a good project to me, been there with the cleaning off of stuff that is not worth it but you just have to use it if its there Smile you can not go out and buy what you have there in your shop eh lol, well I can't anyway.

 Looking forward to seeing the finished thing .
  Cheers Mick
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 1 user Likes f350ca's post:
EdK (11-19-2014)
#26
11-18-2014, 07:41 PM
More tube cleaning and we have the size established. Had planned on 8 feet long but looks like it will be 7 foot 7 inch by 46 wide. Drilled the side rails and welded in 3/4 pipe for stake pockets, easier than cutting square holes that line up top to bottom.

[Image: IMG_1504.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
#27
11-19-2014, 07:43 AM
Greg, you could say it's 231cm x 117cm, sounds bigger that way, No? Blush

Smiley-eatdrink004
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
Mayhem Offline
purveyor of mischief
******
Posts: 4,683
Threads: 93
Joined: Feb 2012
Location: Perth, Australia
The following 2 users Like Mayhem's post:
EdK (11-19-2014), f350ca (11-19-2014)
#28
11-19-2014, 08:24 AM
(11-19-2014, 07:43 AM)stevec Wrote: Greg, you could say it's 231cm x 117cm, sounds bigger that way, No? Blush

Smiley-eatdrink004

Is that what you tell the ladies Steve???

Big Grin
Hunting American dentists since 2015.
Reply
Thanks given by:
stevec Offline
69 yr. old senior
*****
Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada
The following 2 users Like stevec's post:
EdK (11-19-2014), f350ca (11-19-2014)
#29
11-19-2014, 07:01 PM
Darren, you must have me confused with someone much younger than I. Rotfl

I no longer TELL the ladies anything I just obey what my lady tells me. Worthy

Smiley-eatdrink004
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
f350ca Offline
Senior
*****
Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario
The following 2 users Like f350ca's post:
Mayhem (11-22-2014), DaveH (11-22-2014)
#30
11-21-2014, 09:16 PM
Been busy with other peoples projects, but they help pay the bills. Cut the parts for the steering knuckles out of 3/8 plate, the cnc plasma table shines on stuff like this, if you can draw it it will cut it. 

[Image: IMG_1508.jpg]

Decided to weld them up then handle the drilling as if they were castings. Will be easier to get the holes for the king pins lined up this way.
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 10 Guest(s)