Todays Project - What did you do today?
Dave is many things, most of which we don't want to know about. Big Grin

Ed
Reply
Thanks given by:
Nice work on the collet chuck, Chuck. I built one for my SB lathe and it sure is nice having the repeatability when you have to remove and replace the peice your working on.

Shawn
Shawn, proud to be a member of MetalworkingFun Forum since Nov 2013.
Reply
Thanks given by: chucketn
here's another find pile of junk that I created today. most of this is going in the trash.

   

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Ed, Please delete the above two posts by me.
The comments I tried to post didn't show up (is this a defense mechanism?)
Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.
Reply
Thanks given by:
had one of those weird jobs rear its ugly head today that you think won't really be a problem until you get started on it and find out that you don't have the one tool you need to actually fix what it is that your working on.

Well I needed a bearing spliter and the one I have which will fit some pretty big stuff wouldn't work, so I made one to pull a sleave off a probably 5/16" shouldered stud.

Its not pretty but it worked and that's all that counts for a one time use tool. nice thing is the puller I made a spell back is almost big enough to work with it.

     

First try was made out of 1018 flat bar, the edge pulled out of it, the one in the photo is made from a couple little fall off piece's from a trailer spring that I have been sawing up making some parts for a Highwall I'm working on.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Assembled one of the wall sections in the shop where I had the aid of the overhead crane. Looks like they'll go together easily.
Now have to move it in one chuck. 

[Image: IMG_1433.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:
poured some iron today that turned out like it was suppose to nice and gray the days pour, the flask the pestle was in floated so it has a sunk n spot where the iron ran out of the mold cavity, its still a useable part just not round in the one spot.
   

snapped gate to check color of iron nice and gray with a nice small tight grain structure
   

what was poured into the ingot mold I sawed the end off of it.
   

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
Greg , the frame looks very smart , good looks and very robust , I bet its some weight to move about now. It shoulld last for many a year, Job well done.

dallen , that cast looks perfect to me , not a mark in the bits sawn through, hope it machines as good as it looks.

 Cheers Mick.
Micktoon, proud to be a member of MetalworkingFun since Sep 2012.
Reply
Thanks given by:
(10-04-2014, 03:44 PM)Micktoon Wrote: dallen , that cast looks perfect to me , not a mark in the bits sawn through, hope it machines as good as it looks.

 Cheers Mick.

Mick, with the ease that it sawed, it will machine with no problem. the parts only needed to have the flash cleaned off of them, although the one that the cope floated on needed a good deal of grinding to cleanup.

Nothing better then when a pour turns out like its suppose too.

DA
dallen, proud to be a member of MetalworkingFun Forum since Apr 2012.

If life seems normal, your not going fast enough! Tongue
Reply
Thanks given by:
A wet morning but did some assembly after lunch. Your right Mick, that frame was a bit of a bear to move. The rest will be assembled on site.

[Image: IMG_1435.jpg]
Free advice is worth exactly what you payed for it.
Greg
Reply
Thanks given by:




Users browsing this thread: 28 Guest(s)