Building an Aligator

Pages (11): « Previous 1 2 3 4 5 6 7 8 ... 11 Next »

Thread Modes

Building an Aligator

Hawkeye Offline

Junior

Posts: 535
Threads: 39
Joined: Jan 2013
Location: Kelowna, BC, Canada

The following 2 users Like Hawkeye's post:
EdK (05-25-2014), DaveH (07-08-2014)

#11

05-25-2014, 04:47 PM

"Coffee" and "Lunch".

Mike

If you can't get one, make one.

Hawkeye, proud to be a member of MetalworkingFun Forum since Jan 2013.

Like Post

f350ca Offline

Senior

Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario

#12

05-25-2014, 09:22 PM

(05-25-2014, 01:06 PM)stevec Wrote: Greg, would the two whistles be of different pitch signalling different horrific things about to happen?

Probably Sh** and OH Sh**

Free advice is worth exactly what you payed for it.
Greg

Like Post

f350ca Offline

Senior

Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario

#13

07-07-2014, 10:20 PM

The project continues. Found a sawmill that had white oak for the bottom planking and skids. Now looking for a planer mill to do a ship lap edge.

Free advice is worth exactly what you payed for it.
Greg

Like Post

stevec Offline

69 yr. old senior

Posts: 2,685
Threads: 29
Joined: Feb 2012
Location: Nova Scotia, Canada

#14

07-08-2014, 05:50 AM

(07-07-2014, 10:20 PM)f350ca Wrote: Now looking for a planer mill to do a ship lap edge.

Greg, are you looking through YOUR shops? Rotfl

Busy Bee 12-36 lathe, Busy Bee Mill drill, Busy Bee 4x6 bandsaw, Homemade 9x17 bandsaw, Ad infinitum.

Like Post

f350ca Offline

Senior

Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario

The following 1 user Likes f350ca's post:
stevec (07-08-2014)

#15

07-08-2014, 08:23 AM

(07-08-2014, 05:50 AM)stevec Wrote:
(07-07-2014, 10:20 PM)f350ca Wrote: Now looking for a planer mill to do a ship lap edge.

Greg, are you looking through YOUR shops?

Could be. I think I have one somewhere, just can't put my finger on it. Or was that at your shop.

Free advice is worth exactly what you payed for it.
Greg

Like Post

f350ca Offline

Senior

Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario

The following 3 users Like f350ca's post:
DaveH (07-21-2014), EdK (07-21-2014), stevec (07-21-2014)

#16

07-21-2014, 12:43 PM (This post was last modified: 07-21-2014, 12:44 PM by f350ca.)

I guess this is now a serious project.
Bill bought the white oak and had it milled with a ship lap edge for the bottom, thats the stack to the right. Under the 2x4s to the left is 2x6 white oak for the skids and internal frame work.
Went down this morn and Bill and I started laminating the sides, 2x4 spruce stacked on the flat, with butyl caulking between. The sides are 28 feet long with a taper front and back to give 18 feet on the bottom.
[Image: IMG_1262.jpg]

Free advice is worth exactly what you payed for it.
Greg

Like Post

f350ca Offline

Senior

Posts: 3,003
Threads: 51
Joined: Apr 2012
Location: Ontario

#17

07-28-2014, 12:43 PM

Got a couple of hours in at the boat this morning. Tom and I made good progress. This side has all the 2x4s in place, still two layers of 2x6 white oak to go on the bottom and the ends, after they're cut to shape.

[Image: IMG_1281.jpg]