MetalworkingFun Forum › Machining › General Metalworking Discussion v
Let's See Your Shop

Thread Modes
Let's See Your Shop
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#251
06-17-2014, 05:25 AM
(06-16-2014, 09:52 PM)kenne Wrote: For some reason I can't seem to upload more than one photo at a time , it says they are too large , ( haven't heard that for a while:) ...

There's a size limit for pictures. Those you posted are huge. You should scale them down a bit then you should be able to upload more than one per post. The image limit per post is 15.

Ed
Reply
Thanks given by:
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#252
06-17-2014, 07:51 AM
Arbalest,
Nice shop, I really like your anvil and stand Thumbsup
Smiley-eatdrink004
DaveH
Reply
Thanks given by:
Highpower Offline
JAFO
******
Posts: 4,460
Threads: 184
Joined: Feb 2012
Location: Missouri, USA
#253
06-17-2014, 09:25 AM
(06-17-2014, 07:51 AM)DaveH Wrote: Arbalest,
Nice shop, I really like your anvil and stand Thumbsup
Smiley-eatdrink004
DaveH

Smiley-signs009 Smiley-signs064 Drool
Willie
Reply
Thanks given by:
kenne Offline
Sophmore
***
Posts: 97
Threads: 5
Joined: Jun 2014
Location: las vegas burbs
#254
06-17-2014, 10:43 AM
(06-17-2014, 05:25 AM)EdK Wrote:
(06-16-2014, 09:52 PM)kenne Wrote: For some reason I can't seem to upload more than one photo at a time , it says they are too large , ( haven't heard that for a while:) ...

There's a size limit for pictures. Those you posted are huge. You should scale them down a bit then you should be able to upload more than one per post. The image limit per post is 15.

Ed

Thanks , I will figure out how to do this and make them smaller ,I would like to blame the technology ,but it's the nut behind the wheel again .
kenne, proud to be a member of MetalworkingFun Forum since Jun 2014.
Reply
Thanks given by:
kenne Offline
Sophmore
***
Posts: 97
Threads: 5
Joined: Jun 2014
Location: las vegas burbs
The following 2 users Like kenne's post:
stevec (06-17-2014), Mayhem (06-17-2014)
#255
06-17-2014, 10:58 AM (This post was last modified: 06-17-2014, 11:00 AM by kenne.)
                    Here we go again , sorry I am not trying to be a pain , but I want to get this right.
finally got it right , I will send more photo's when the shop is cleaned up and the rest of the tools are uncovered and moved , thanks for the patience .......
kenne, proud to be a member of MetalworkingFun Forum since Jun 2014.
Reply
Thanks given by:
EdK Offline
Whipping Boy
*******
Posts: 8,860
Threads: 319
Joined: Feb 2012
Location: Arizona/Minnesota
#256
06-17-2014, 11:43 AM
Good job on resizing the pictures. Thumbsup

Nice shop space kenne but I'm not seeing anything needing cleaning. 17428

Ed
Reply
Thanks given by: kenne
DaveH Offline
Child of the 60's
******
Posts: 4,513
Threads: 139
Joined: Feb 2012
Location: Kempton Park. South Africa
#257
06-17-2014, 12:57 PM
Very nice Kenne Thumbsup Looks nice and clean to me.
Smiley-eatdrink004
DaveH
Reply
Thanks given by: kenne
pineyfolks Offline
Freshman
**
Posts: 10
Threads: 1
Joined: Aug 2013
Location: Dillonvale
The following 2 users Like pineyfolks's post:
PixMan (07-28-2014), DaveH (07-28-2014)
#258
07-28-2014, 11:08 AM
Here's a few pics of my place


Attached Files Thumbnail(s)
                       
pineyfolks, proud to be a member of MetalworkingFun Forum since Aug 2013.
Reply
Thanks given by:
pineyfolks Offline
Freshman
**
Posts: 10
Threads: 1
Joined: Aug 2013
Location: Dillonvale
The following 2 users Like pineyfolks's post:
PixMan (07-28-2014), stevec (07-29-2014)
#259
07-28-2014, 11:13 AM
A few more


Attached Files Thumbnail(s)
               
pineyfolks, proud to be a member of MetalworkingFun Forum since Aug 2013.
Reply
Thanks given by:
PixMan Offline
Resident Pariah
******
Posts: 2,344
Threads: 53
Joined: Feb 2012
Location: Spencer MA USA
#260
07-28-2014, 11:25 AM
Nice shop!! So roomy, I'm envious of that.

Your bench for the (South Bend?) bench lathe is one of the best I've seen, having those drawers right there. Tell me about the surface grinder, I've never seen one with that configuration. Also, what is the "Rotex" machine? Hard to tell, but does appear to have a big motor for such a small machine.

Your saws are very nice, truly "industrial grade" stuff. Is the horizontal with the roller tables a Cosen or Amada? The vertical a Grob?
Reply
Thanks given by:




Users browsing this thread: 1 Guest(s)