+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Metrology (http://www.metalworkingfun.com/forum-33.html)
+--- Thread: Latest addition - NOS gage blocks (/thread-2962.html)
Latest addition - NOS gage blocks - JScott - 11-19-2015
I found a good buy on some new, old stock gage blocks on eBay last week. Made an offer and got this little 36 piece set for a nice price. They are Chinese made, Grade B but they are still in the original preservative wrappings. It takes a block or two more to build a stack but this will be a nice little set for my home shop.
This set has a series of blocks that go from 0.1001" to 0.1009" just in case I need to do some aerospace work!
At present I have a 12x18x3 inch thick granite surface plate, a 36 piece set of spacer blocks, these new gage blocks and a surface gage. Next up is a dial height gauge.
Thanks for looking, JScott.
[attachment=12242]
[attachment=12243]
[attachment=12244]
[attachment=12245]
RE: Latest addition - NOS gage blocks - CNCAZ - 11-19-2015
I used to have two sets. The 36 piece and a much larger set, don't recall how many.
I always found myself using the small set as it was more convenient. Finally sold the large set and never missed it.
I bet you get along just fine with the set you have.
I use round space blocks as much as the jo blocks.
RE: Latest addition - NOS gage blocks - Highpower - 11-19-2015
Good enough for a home shop for sure.
I've got 3 different sets of gauge pins, but not a single gauge block.
RE: Latest addition - NOS gage blocks - TomG - 11-19-2015
Definitely good enough for shop use, but I would do a sanity check on them just the same. After all, they were made in China. Clean them and check them with a good, well calibrated tenth reading micrometer. You should make sure they all measure up to what they say they are before trusting them.
Tom
RE: Latest addition - NOS gage blocks - wawoodman - 11-19-2015
(11-19-2015, 02:03 PM)CNCAZ Wrote: I used to have two sets. The 36 piece and a much larger set, don't recall how many.
I always found myself using the small set as it was more convenient. Finally sold the large set and never missed it.
I bet you get along just fine with the set you have.
I use round space blocks as much as the jo blocks.
I've got a set of the round ones, too. They seem fine for my use.
RE: Latest addition - NOS gage blocks - JScott - 11-20-2015
(11-19-2015, 07:03 PM)TomG Wrote: Definitely good enough for shop use, but I would do a sanity check on them just the same. After all, they were made in China. Clean them and check them with a good, well calibrated tenth reading micrometer. You should make sure they all measure up to what they say they are before trusting them.
Tom
Tom,
Really good advice. They came with an inspection certificate so in theory somebody checked them to ±0.000050". The certificate shows them to be in spec.
I have a nice, low mileage Starrett 0-1 tenth mike and I'll be able to check everything up to 1". I'll just have to trust the 2" and 4" blocks but they probably won't get much excercise anyway.
JScott
RE: Latest addition - NOS gage blocks - krv3000 - 11-21-2015
brill
RE: Latest addition - NOS gage blocks - Jurskas - 04-05-2016
(11-19-2015, 09:49 AM)JScott Wrote: I found a good buy on some new, old stock gage blocks on eBay last week. Made an offer and got this little 36 piece set for a nice price. They are Chinese made, Grade B but they are still in the original preservative wrappings. It takes a block or two more to build a stack but this will be a nice little set for my home shop.
This set has a series of blocks that go from 0.1001" to 0.1009" just in case I need to do some aerospace work!
At present I have a 12x18x3 inch thick granite surface plate, a 36 piece set of spacer blocks, these new gage blocks and a surface gage. Next up is a dial height gauge.
Thanks for looking, JScott.
After checking the blocks up to 1" you can wring them and check the larger blocks with a indicator and surface gage on your plate. Its not the most accurate way but will suffice for any hobby home work.
Eric
RE: Latest addition - NOS gage blocks - JScott - 04-06-2016
Jurskas, Thanks for the tip. It will help me finish the last check on the blocks. I haven't started yet due to other projects but I will get to it.