MetalworkingFun Forum
Elliott Concord 460 lathe - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machinery (http://www.metalworkingfun.com/forum-10.html)
+--- Forum: Lathes (http://www.metalworkingfun.com/forum-11.html)
+--- Thread: Elliott Concord 460 lathe (/thread-2673.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12


RE: Elliott Concord 460 lathe - Mayhem - 09-07-2016

You know me - I like a challenge Big Grin

A lot of the stuff in those boxes isn't for me but those who want it will spring for the postage, regardless of whether some of my stuff gets thrown in. This time I am aware of the rules that thwarted me last time. I can throw two items in the cargo hold on the plane, each weighing in at 23kg (50.6lb) max. I plan to travel light coming out Big Grin


RE: Elliott Concord 460 lathe - Darryl Ovens - 09-12-2022

Hi there,

I bought a short bed version of the Concord 460 about 15 years ago.
Mine had been "stored" under a cheap cover outside and forgotten for several years.
[Image: image.gif]The cover had disintegrated and the rain had gone into the gearboxes via the speed change gear levers and the oil distribution galleries.  So water was distributed through everything important in the headstock and "Norton" box. There was so much water that there was no oil left in the oil tank under the machine.
[attachment=17990]
(I have attempted to insert before and after photos of the headstock gearbox and one spindle cup race after cleaning but before regrinding,  but cannot figure out how to control their placement.)
Needless to say I got it very cheap and a new replacement Timkin taper roller bearing (one cone only) for the spindle, cost as much as the lathe did!
[Image: image.gif]After a complete dismantle, and electrolysis cleaning of the headstock and Norton gearboxes (gears, shafts, bearings etc), plus removal of rust from the rest of the machine, it has turned out to be a really nice accurate machine to use.
[Image: image.gif]Removing the spindle was a challenge, as it looks like they assembled the bearings on the spindle and then pressed the assembly into the headstock.  I had to cut the big key in the largest gear on the spindle into several pieces about an inch long, (while still in place), in order to get the spindle out of the gears and bearings.  
[Image: image.gif]Then on reassembly I had no specs for things like spindle bearing preload, so had to guess them by what felt likely.
Haha, I also learnt the hard way, about the oil held in the cover.  Luckily I had already removed the power switch box by this stage, but I did notice the switch box was damp with oil inside.
As I can only get single phase power here I've been driving it with a 3 hp single phase motor.  I had to back off the clutches as much as reasonable (which took many adjustments),  to try to reduce the clutch drag as much as possible, as the motor is struggling!
Ultimately I'll put a single phase to three phase electronic drive, and reinstall the original 12 hp motor.

However it has done a range of odd ball jobs, from re-machining trailer axil seal surfaces, (the big spindle bore allowed the axil to be passed through the headstock), to mostly, machining stationary engine parts; ie a new 24" flywheel, 7' dia (by 16" long piston), ring grooves and rings, and down to ignition hot tubes in Stainless Steel.

I only stumbled on this thread yesterday and was reading it with great interest, but found it stopped suddenly, just as it was getting interesting.    Smiley-signs131 

I'd love to hear how the rest of it went, did you get it sorted and set up, how has it been over the years since 2016?
I hope it went well.

Cheers
Darryl


RE: Elliott Concord 460 lathe - EdK - 09-12-2022

Wow! Nice job on the restore!  Thumbsup

This thread will help you with inserting pictures into posts:

Inserting Pictures Into Posts

Oh, and  Welcome to the forum Darryl.

Ed


RE: Elliott Concord 460 lathe - Highpower - 09-12-2022

Wow indeed!

Very impressive job you did there Darryl.

Smiley-signs046


RE: Elliott Concord 460 lathe - Dr Stan - 09-12-2022

Very very nice. Thumbsup


RE: Elliott Concord 460 lathe - Darryl Ovens - 09-12-2022

Thanks for your comments.

I have to admit to having served a fitter turner apprenticeship with the naval dockyard in Auckland, and these days while not being "on the tools" much professionally, I have an interest in restoring vintage machinery (esp engines), which may have spent several tens of years out in the weather.
So this lathe at only a couple of years outside was still quite good (compared to some of the other machinery) and cleaned up really well.
I have seen a lot of damage done by powered wire brushes and sand blasting used on machined surfaces, where the judicial use of electrolysis could have removed the rust pits without damaging/affecting the surrounding surfaces, resulting in parts that can sometimes come back to looking almost like new.  
I say "looking like" as there can be small (microscopic) "holes" remaining were the rust was, and sometimes, if in critical places, these can be stress raisers.  This plus a slight risk of hydrogen embrittlement on high strength steels, means you want to be a little careful as to what parts electrolysis should/can be used on.

To practice putting photos in.  (Thanks for the link to the inserting photos thread).
[attachment=17995]
Here is my star engine restoration. 
Imported to NZ around 1905 by my grandfather, so it is also something of a family arloom (sp).  My father (born 1931), could only just remember it running in the late 1930's.  This one spent something nearer to 60 years out in the weather and you can just see one of the rust pits in the side shaft at the edge of the pulley.  
I contemplated renewing the shaft but decided it was now part of the character of this engine.  
Ditto the blowhole in the main casting just beside the cylinder drip feeder.

Cheers Darryl


RE: Elliott Concord 460 lathe - Dr Stan - 09-12-2022

A beautiful restoration. You deserve to be proud of your work. Thumbsup Smiley-eatdrink004


RE: Elliott Concord 460 lathe - rleete - 09-13-2022

Very nice work.


RE: Elliott Concord 460 lathe - Vinny - 09-13-2022

Welcome to the forum!!