MetalworkingFun Forum
cutter breakage - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: cutter breakage (/thread-2518.html)

Pages: 1 2


cutter breakage - how'sitwork? - 02-15-2015

I recall reading somewhere recently that too slow a speed leads to cutter breakage. Having just boobed and broken ( snapped) a 3/4 by 3 in long end mill ( I engaged the auto up feed by accident when milling some aluminium- took a BIG BITE THEN SNAPPED before I realized what I had done ).
Can someone Shed any light on this? Tom ???

I can follow why too slow a feed might lead to heat and blunting of cutter but too slow a speed leading to snapping?

Moral of story- don't rush especially when engaging auto feed. My mill can autofeed the table up as well as cross feed.


RE: cutter breakage - Baron - 02-15-2015

Ouch ! Expensive mistake.


RE: cutter breakage - DaveH - 02-15-2015

Well that is a sad thing to happen.

The spinning cutter(s) have to be able to clear (cut) the material away.

If the cutter is not spinning (ie stationary) with a depth of cut and the work piece is fed into the cutter something is going to break. Which is why your cutter broke the spindle speed wasn't fast enough for the the feed.

So spindle speed is important with respect to the feed.

If it is a HSS cutter going too fast will cause heat and blunt the cutter.

Still sorry your cutter broke.
Smiley-eatdrink004 
DaveH


RE: cutter breakage - Highpower - 02-15-2015

(02-15-2015, 04:37 PM)how Wrote: I can follow why too slow a feed might lead to  heat and blunting of cutter but too slow a speed leading to snapping?

Moral of story- don't rush especially when engaging auto feed. My mill can autofeed the table up as well as cross feed.

(02-15-2015, 05:28 PM)DaveH Wrote: If the cutter is not spinning (ie stationary) with a depth of cut and the work piece is fed into the cutter something is going to break. Which is why your cutter broke the spindle speed wasn't fast enough for the the feed.

So spindle speed is important with respect to the feed.


Smiley-eatdrink004 
DaveH

As is the spindle directionBash

Don't rush indeed, and don't ask me how I know....  Blush

[Image: Half-inch_end_mill.jpg]


RE: cutter breakage - PixMan - 02-15-2015

Chip load per tooth.

Too high = excess load and the cutter "hogs in" and breaks
Too low = rub the sharp edge dull


RE: cutter breakage - Sunset Machine - 02-16-2015

That's it in a nutshell - chip load. My mill has the table feed driven by the spindle; going at too slow of an RPM does no harm at all, other than waste time.


RE: cutter breakage - how'sitwork? - 02-16-2015

OK guys, thanks for the explanation. Didn't expect Aluminium to break HSS but it did try to take a big bite!

Live and learn.

Willie - I feel your pain!


RE: cutter breakage - Highpower - 02-16-2015

(02-16-2015, 01:55 PM)how Wrote: Willie -  I feel your pain!

And I feel yours. But we'll both remember in the future eh? Happyyes

Smiley-eatdrink004


RE: cutter breakage - Vinny - 02-16-2015

I did that once with what I thought was my last 1/8" endmill. I was lining something up and forgot that I had the table up for the next cut. The mill wasn't even on. When I heard that "snap" many 3, 4, 5 and 7 letter words immediately followed. So I ordered up 4 more and the nite before they were delivered I thought to look in this box of misc endmills. Yep, six more in there. Grrr. I broke the second one with too fast a feed for the spindle speed just like How did. I was only milling plastic!


RE: cutter breakage - TomG - 02-16-2015

Too high a chip load per tooth is what breaks end mills, but ensuring that the end mill is running at the proper rpm GREATLY reduces the chance of that happening. A 3/4" end mill cutting aluminum should be running at over 2000 rpm. Anything less is asking for trouble. You'll still need to make sure the chips clear out, so coolant may be appropriate as well.

Tom