+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machinery (http://www.metalworkingfun.com/forum-10.html)
+--- Forum: Other Machinery (http://www.metalworkingfun.com/forum-13.html)
+--- Thread: Tool and Cutter Grinder (/thread-2027.html)
Pages:
1
2
Tool and Cutter Grinder - Hawkeye - 02-26-2014
Some years ago, I started to build a tool and cutter grinder, mostly with a view to sharpening endmills. I needed to make a rotary table to mill a curved slot, so I set the grinder project aside. I finished the RT, but never got back to the grinder. This is as far as I got. That's an R8 spindle, since I have a full set of R8 collets.
[attachment=7814]
Today, I had a day off so I decided to make the grinder spindle. I figured an MT2 socket would be the most versatile in order to mount whatever I may need to spin as the project grows. I roughed the taper at around 1 1/2*, to be trued up with a tapered reamer.
[attachment=7810]
It took quite a while to ream out the MT2 socket, but it came out quite nice.
[attachment=7811]
I got to try out my new swing-up threading tool to cut the pre-loading thread.
[attachment=7812]
The finished spindle. Next step is the body that the bearings mount in.
[attachment=7813]
RE: Tool and Cutter Grinder - stevec - 02-26-2014
Hawk, Is yours designed after this?
[attachment=7815]
It's the kind I have. Is your R-8 spindle (the one that holds the endmill, or whatever) going to have compressed air to allow it to "float" and move freely?
RE: Tool and Cutter Grinder - Hawkeye - 02-26-2014
I think I tried to incorporate some of the features of that one, plus some from other sources. I tried injecting air, but it didn't make the spindle move any easier. I haven't seen any plans for an air spindle.
RE: Tool and Cutter Grinder - stevec - 02-27-2014
Experience has led me to believe that if there is enough clearance between the spindle and the bore you end up with play/potential movement that leads to inaccurate grinding. That said it still ads a lot of life to end mills and allows me to reserve my new ones for more precise precision work.
RE: Tool and Cutter Grinder - Hawkeye - 03-09-2014
I spent some time today making the bearing carrier for the spindle. I really need to get some more tapered-shank drill bits. They are the best way to drill large holes on the lathe.
[attachment=7879]
The usual boring work to make the through-hole and the two pockets for the bearings. I managed to sneak up on the pocket diameters for a press fit on both bearings.
[attachment=7880]
The fit was tight enough that the arbor press wouldn't quite do it, but the hydraulic press had no trouble at all.
[attachment=7881]
I figured I'd better check the runout, so I set it up as shown. Unfortunately, there is about 0.006" TIR. I'll see what I can do to improve that. It's possible that the economy bearings have some runout.
[attachment=7882]
RE: Tool and Cutter Grinder - Old Iron - 03-09-2014
That is going to be a nice setup when you get it finished.
Paul
RE: Tool and Cutter Grinder - Hawkeye - 03-09-2014
Bummer! I mounted the pulley end of the spindle in the MT3 collet on the lathe, then tried to slide the steady onto the bearing carrier.
[attachment=7883]
The through-hole is not centred on the lathe spindle.
Plan B. I clamped the carrier to the compound, with appropriate shims. That held it solidly while I touched up the MT2 socket with the tapered reamer.
[attachment=7884]
Still reading 0.005" TIR in the test setup, but a ground centre in the socket measures 0.003". It's important to note that this spindle is for the grinding wheel, not for the toolholder. If it's off a couple of thou, it will still work, more like a flycutter. The cup wheel can be trued up, but would have to be repeated each time the wheel is remounted.
RE: Tool and Cutter Grinder - stevec - 03-10-2014
(03-09-2014, 10:05 PM)Hawkeye Wrote: The cup wheel can be trued up, but would have to be repeated each time the wheel is remounted.
I agree and I doubt if a wheel could be remounted without needing to be trued even if the spindle was dead nuts on.
RE: Tool and Cutter Grinder - Hawkeye - 03-10-2014
That's pretty much what I was thinking.
RE: Tool and Cutter Grinder - Dr Stan - 08-10-2014
(03-10-2014, 06:13 AM)stevec Wrote:(03-09-2014, 10:05 PM)Hawkeye Wrote: The cup wheel can be trued up, but would have to be repeated each time the wheel is remounted.
I agree and I doubt if a wheel could be remounted without needing to be trued even if the spindle was dead nuts on.
There's enough clearance between the hub of the wheel and the spindle nose to necessitate redressing after each mounting of the wheel. Its a trade practice on grinders in general. I even true up my pedestal grinder wheels with a diamond dresser. Makes for easier and better HSS tool sharpening.