+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: More woodcarving (/thread-1372.html)
More woodcarving - Micktoon - 05-07-2013
Good evening all , I have been doing a new woodcarving project, after the skull carving I wanted to do something different so decided on a flat plaque with a heraldic rampant lion on it in low relief. I have traced it from a photo in a book and that just happened to be the right size for a bit of lime wood I had, I think its called Linden wood in the U.S .
I started by tracing the drawing onto the slab of wood , then bandsawed it into a round shape and turned it true, then turned in a detail to form a rim to the outer edge of the peice on the wood turning lathe.
This is the blank after being turned on the lathe, I think it ended up under six inches ( 150mm ) overall.
![[Image: Latheinverter001.jpg]](http://s1167.photobucket.com/user/micktoon/media/Latheinverter001.jpg.html)
I then decided to put it back on the lathe and turn a recess around the lion so I had a constant depth to aim for around the whole background, this would make it easier to keep the depth constant.
![[Image: lathecogs001.jpg]](http://s1167.photobucket.com/user/micktoon/media/lathecogs001.jpg.html)
I attached a square block to the back so it can be held in the carving vice for working on.
![[Image: lathecogs002.jpg]](http://s1167.photobucket.com/user/micktoon/media/lathecogs002.jpg.html)
Then its a case of going around the outline of the subject with the V tool.
![[Image: lathecogs003.jpg]](http://s1167.photobucket.com/user/micktoon/media/lathecogs003.jpg.html)
Once thats is done as much as you can get into with the V tool its a case of removing the background so that just the design will stand proud, I am already thinking this should have been twice the size as its really fiddly and very easy to chip bits off you want to keep unless every cut is thought about with reference to grain direction. With the carving having the square on the back it can be rotated to make the direction of cuts easier.
![[Image: lathecogs004.jpg]](http://s1167.photobucket.com/user/micktoon/media/lathecogs004.jpg.html)
![[Image: lathecogs005.jpg]](http://s1167.photobucket.com/user/micktoon/media/lathecogs005.jpg.html)
This is the stage I have reached so far , its taken a good few hours, when finished the plan is the background will either be left tool finish with small scoop marks off the gouge or maybe punched with a chequered punch as leatherworkers or silversmiths use and the lion will be rounded off and made as 3D as the depth will allow. Its proving to be far more tricky than I thought it would be so going slowly.
![[Image: bronzedisc004.jpg]](http://s1167.photobucket.com/user/micktoon/media/bronzedisc004.jpg.html)
Cheers Mick.
RE: More woodcarving - EdK - 05-07-2013
Nice start Mick.
Ed
RE: More woodcarving - DaveH - 05-07-2013
Looking good Mick.
I was wondering if you could show us some of the tools you use, such as a V tool.
DaveH
RE: More woodcarving - Mayhem - 05-08-2013
Looking good Mick
RE: More woodcarving - Micktoon - 05-08-2013
(05-07-2013, 06:43 PM)DaveH Wrote: Looking good Mick.
I was wondering if you could show us some of the tools you use, such as a V tool.
DaveH
No problem Dave I will take some photos of the tools next time I am carving, some of them are from the 1870's although they look no different to new ones really.
Cheers Mick.
RE: More woodcarving - sasquatch - 05-08-2013
Nice Mick, waiting to see the pics also.
RE: More woodcarving - krv3000 - 05-09-2013
as per mick well dun