Peerless Shaper - Printable Version +- MetalworkingFun Forum (http://www.metalworkingfun.com) +-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html) +--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html) +--- Thread: Peerless Shaper (/thread-2819.html) |
RE: Peerless Shaper - f350ca - 10-19-2015 I think the blueing worked well, will have to see how it stands the test of time. The number stamping was another story. The mystery metal shafting I used is fairly hard, so the stamping isn't that deep. RE: Peerless Shaper - dallen - 10-20-2015 looks good RE: Peerless Shaper - f350ca - 10-20-2015 The reference mark made. RE: Peerless Shaper - f350ca - 10-27-2015 Its together and moved into its spot, now have to arrange things around it. Its first cut, but not the deepest. Haven't worked it hard yet, but a 20 thou cut makes no difference in the sound of the machine. One disappointing feature though, the minimum side travel is 15 thou per stroke, will be using a shear tool a lot. RE: Peerless Shaper - DaveH - 10-27-2015 Came out very nice Greg DaveH RE: Peerless Shaper - Mayhem - 10-27-2015 Nice work Greg. Looks to clean though RE: Peerless Shaper - Vinny - 10-27-2015 Lookin good Greg. But I've always heard "The First Cut is the Deepest". RE: Peerless Shaper - f350ca - 10-28-2015 Thanks guys, don't worry I'll soon have it dirtied up. A short clip of her cutting. A nice easy .05 depth of cut at .015 feed rate. https://youtu.be/RSD4dOX6H38 RE: Peerless Shaper - dallen - 10-28-2015 Greg; looks like you got yourself a nice shaper out of all the elbow grease RE: Peerless Shaper - Dave D - 11-13-2015 Hi again Greg, as you suggested I'm posting in the thread now. I live just outside of Vancouver and like you I found a few old posts or KIJJI/Craigslist adds for the smaller version of this shaper. If you Google Peerless shaper you usually end up with most results for "Peerless" of USA power hacksaw fame. There was someone else in Vancouver with the same 16/18 Peerless shaper but I have lost contact with them so there are at least 3 in existence. It would be great if somewhere out there there is some sales literature or ads about these shapers. I have only used my 16/18 a little and still need to attach some small things like the wipers and some minor repairs. Apart from replacing the worn out acme thread on the compound/head slide and requiring some new lubrication mine was basically in working condition. So far, I've only partially taken apart the table, head slide and not much else. - The cross feed is definitely a coarse feed and like yours the vertical power feed only works in the down direction. I've toyed with the idea of using a finer ratchet mechanism with a longer lever arm or a pneumatic cylinder under the table to lighten it. The crank handle I have has been repaired or replaced and it looks like it is shorter than it should be. I can't imagine having to crank the table back up with much weight on it. - The ram on mine will creep in neutral when cold which appears to be due to the oil viscosity. - In high gear I do get a little gear noise from the transmission. I was told by the previous owner that mine was made during WW II and subsequently that is why the transmission speed plate on mine is plastic. Your brass plate looks a lot cooler. I haven't really looked yet but did you ever come across a serial number? The appearance of the top part of the compound head slide on mine looks like it was machined out of a large chunk of steel and not cast. Maybe it was a shop made replacement due to a crash or maybe if it was made during the war that is all they had on hand. I will try to post pictures of the vice and shaper in the next week or so. The vice is definitely a big, heavy sucker. Again, thanks for the post about your shaper and you did a great job on the restoration. Dave |