MetalworkingFun Forum
ER-40 Collet Chuck For My Lathe - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machinery (http://www.metalworkingfun.com/forum-10.html)
+--- Forum: Lathes (http://www.metalworkingfun.com/forum-11.html)
+---- Forum: Lathe Tooling (http://www.metalworkingfun.com/forum-19.html)
+---- Thread: ER-40 Collet Chuck For My Lathe (/thread-803.html)

Pages: 1 2 3 4 5 6

RE: ER-40 Collet Chuck For My Lathe - EdK - 03-09-2013

(03-09-2013, 05:20 PM)stevec Wrote: How can you tell? There's a black box with a white triangle covering it!
Rotfl

I'm not so dumb, hmmm. Chin

Rotfl

Ed

RE: ER-40 Collet Chuck For My Lathe - doubleboost - 03-09-2013

(03-09-2013, 05:24 PM)EdK Wrote:
(03-09-2013, 05:20 PM)stevec Wrote: How can you tell? There's a black box with a white triangle covering it!
Rotfl

I'm not so dumb, hmmm. Chin

Rotfl

Ed

I have a broken one i use in my videoes
Smiley-dancenanaSmiley-dancenanaSmiley-dancenanaSmiley-dancenana
That is a very nice job
You should be proud of itDroolDroolDrool
John

RE: ER-40 Collet Chuck For My Lathe - EdK - 03-09-2013

(03-09-2013, 05:29 PM)doubleboost Wrote:
(03-09-2013, 05:24 PM)EdK Wrote:
(03-09-2013, 05:20 PM)stevec Wrote: How can you tell? There's a black box with a white triangle covering it!
Rotfl

I'm not so dumb, hmmm. Chin

Rotfl

Ed

I have a broken one i use in my videoes
Smiley-dancenanaSmiley-dancenanaSmiley-dancenanaSmiley-dancenana
That is a very nice job
You should be proud of itDroolDroolDrool
John

Thanks John. Coming from you with your high standards, I feel rather humbled. Blush

Ed

RE: ER-40 Collet Chuck For My Lathe - krv3000 - 03-09-2013

i stick the pointer dawn

RE: ER-40 Collet Chuck For My Lathe - DaveH - 03-09-2013

Well done Ed, that's really top class Thumbsup Smiley-signs107 Worthy
Smiley-eatdrink004
DaveH

RE: ER-40 Collet Chuck For My Lathe - EdK - 03-09-2013

I chucked up a gauge pin and it shows the same run-out as the ER taper so good enough for this old fart! Happyyes

Ed

RE: ER-40 Collet Chuck For My Lathe - Mayhem - 03-09-2013

Nice work Ed

RE: ER-40 Collet Chuck For My Lathe - krv3000 - 03-10-2013

ho farted

RE: ER-40 Collet Chuck For My Lathe - EdK - 03-10-2013

(03-10-2013, 06:11 PM)krv3000 Wrote: ho farted

I think I did. Rotfl

RE: ER-40 Collet Chuck For My Lathe - Highpower - 03-11-2013

(03-09-2013, 08:29 PM)EdK Wrote: I chucked up a gauge pin and it shows the same run-out as the ER taper so good enough for this old fart! Happyyes

Ed

Show off..... Big Grin

Great job Ed. Smiley-eatdrink004