+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: P&W 1830 Radial in 1/6 scale. (/thread-573.html)
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 07-03-2012
Time to drill the mounting holes, 6 of them. An adapter was needed to mount the 3 inch chuck to the table. I chose nylon for this job for no other reason than its diameter. Pics should tell the story but ask if you don't see something. Next we will transfer the locations and drill and tap the case to 4-40. That was not fun at all.
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - Mayhem - 07-03-2012
Keep them coming Bill. I'm not always sure what you are doing but I am enjoying following the build.
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 07-03-2012
That makes two of us, I'm not always sure either.
The pics above show all the holes but we are only concerned with the ones on the circumferance that mount in in the case. The next to tha last pic with the co-ax gage has a master I made while apprenticing on the Moore Jig Bore. It is .00005 accurate or at least it was, "Billy G"
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 07-03-2012
Let's do it. Pic #1 the tools. I extended the drill an the tap. They are silver soldered. Pic #2 Transfer punching the locations. Pic #3 I needed a long center diill. The ledge is 2.000 deep. Pic#4 using ther drill. Pic #5 Tapping with a guide. Pic #6 Pump assy. in place. Pic #6 Pump was run usting the Drill Press and rubber air nozzle at 900 RPM. It was extremely quiet for running dry. That's it for today, grandkids are here.
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - doubleboost - 07-03-2012
Some very clever work going on there Bill
Keep them coming
John
RE: P&W 1830 Radial in 1/6 scale. - Tony Wells - 07-03-2012
Looks good, Bill. I can almost hear it running.......
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 07-03-2012
Thanks again guys. Here is a nine running. Note to self, do not start like this. Look at the starter cord position. Could cause one big mess.
"Billy G"
http://www.youtube.com/watch?v=omSt8ZiE7vM
RE: P&W 1830 Radial in 1/6 scale. - Tony Wells - 07-03-2012
I always envy you guys who are able to make time to take on these serious project builds. Between the work I have to do, even part time, I always have more stuff in the shop that needs attention than I can get to. I have to get my surface grinder going, I have an air compressor that needs proofing and the pump gone through. I need to run a new 3 phase circuit for my new(to me) air conditioner....and the list goes on. Maybe someday I'll have the time to build something just for fun.
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 07-03-2012
Hang in there Tony, you will get there one day. It has a habit of sneaking up on you.
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - Tony Wells - 07-03-2012
You still planning a trip down to Texas any time soon?