MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552

RE: Todays Project - What did you do today? - Kennyv - 04-29-2016

quick lil fix SS Scribe...  im tryning to sell an 18"  veneer height gauge on flea bay had no bites bc it did not have a scribe. So yesterday at lunch cut Pc stock /  layout  stayed an Hr after work machined free hand this scribe took new pics and bam  re listed . Bout the only thing i have done since Dec  boy i sure miss my Garage being able to fiddle  round in.

RE: Todays Project - What did you do today? - f350ca - 05-05-2016

The neighbour offered me a 100+ foot roll of armoured cable. Looked like it might make a good feed for 50 amp service to the blacksmith shop. We dug it out today, literally, the ends were buried in the ground. To our amazement it wasn't cable in the armour but 8 small plastic tubes and two telephone sized wires.
[Image: IMG_2173.jpg]

Any idea what it would have been, pneumatic  control cable of some sort?

RE: Todays Project - What did you do today? - Vinny - 05-05-2016

If it was a non-metalic armored cable, the telephone wires were tracers for the cable and the tubes were probably intended to be fiber optic conduits. In another lifetime I attended a seminar for ATT and Graybar Electric on fiber optic cabling. They said the tracers were added after some company buried over 1000 miles of fiber optic cable without the tracer and had to find a break in it. Turned out some farmer cut it with a backhoe.

RE: Todays Project - What did you do today? - TomG - 05-12-2016

Finished up a little project at work today that I've been working on for a month or so. It's a manufacturing tool for producing a disposable used in one of our products. The disposable is a standard 96 well microplate (talking biology here) that has microscopic scribed lines on it used as reference points for an instrument we build. The lines are about 5 microns wide (.0002"), three on one axis and one on the other, and cross in the center of each of the 96 wells. They are produced by dragging a ceramic blade across the surface of the plastic plate at precise intervals. I built the first pair of these monstrosities about ten years ago, and production has grown to the point where manufacturing can't keep up, so I did a redesign to include faster, more modern motor controls and an overall larger frame. These two scribers should increase production by about 70% and eliminate the aging and troublesome electronics in the old devices. I don't get involved in electronics and programming that much, but all the usual suspects were too busy, so I took on the project myself. The mechanicals were easy. It's just a carriage with a fence (not shown in the video) to hold the microplates (8), riding on 1" diameter Thompson linear shafting and driven by a large stepper motor via a timing belt. The frame to support everything was made up of 3"X6" 6061 rectangular tubing. The scribing mechanism itself is being reused from the old devices to save time. It is basically a THK linear slide holding a ball bearing pivot with and arm to hold the blade and a rotary solenoid to lift it. It also has a damping mechanism that I designed that uses eddy currents from a ring of rare earth magnets acting on an aluminum disk. It helps to prevent chatter as the blade drags across the plastic surface. The stepper motor controls and the software to run them are from Applied Motion and they work very well. They each have a 100 line program capacity and are responsible for different axes. I made the one for the Y axis a master and the X axis or carriage control is the slave. They are linked together via inputs/outputs in a handshaking arrangement. Basically the Y axis control is responsible for the line spacing on the plates and the X axis control moves the carriage when the blade is in position. It's pretty cool watching the two separate programs communicate with each other on the computer screens. The computers are just for writing and debugging the programs. Once that is done, programs will live in the controllers and the scribers will be stand alone.

Anyway here's a little video showing the one of them in action. The whole debugging thing went much better than expected. I loaded the programs yesterday and had it all working as advertised by lunch time today. I did have one of the software dudes help solve a couple of stubborn issues, but overall it went very well. In the video, the red button has three purposes. A short press homes the X and Y axes, and a long press starts the scribing cycle. The toggle switch selects rows or columns on the plate. The 8 rows each have a single line in the center of the wells and the 12 columns each have three lines spaced .11mm apart. A third press of the button during the scribing cycle will interrupt the program and park the blade at home.

Tom





RE: Todays Project - What did you do today? - Vinny - 05-12-2016

Cool!!

RE: Todays Project - What did you do today? - pepi - 05-13-2016

The forum always amazes me with the talent seen from the members.

RE: Todays Project - What did you do today? - DaveH - 05-13-2016

That's impressive Tom Thumbsup Smiley-signs107 
Smiley-eatdrink004 
DaveH

RE: Todays Project - What did you do today? - EdK - 05-13-2016

I bet that was a fun project for you. Nicely done.

Ed

RE: Todays Project - What did you do today? - TomG - 05-13-2016

Thanks guys. I broke it all down this morning and took a put a DA finish on to make it pretty. It'll be going out for anodizing next week. Spent the afternoon writing an operators manual for it. Sleep

Tom

RE: Todays Project - What did you do today? - Mayhem - 05-14-2016

Haven't really gotten much done of late.  Just trying to clean up and organise a few more things.  I thought however that I'd share some pics of the latest edition to the family:

[attachment=13264]
[attachment=13265]

He's a 10 year old Staffy x Ridgeback who I adopted from a family where he wasn't getting much attention.  I've had him about a month now and he is starting to settle in.  It must have been quite a shock to move from a small family house in the suburbs, to a larger block up in the hills.  The local wildlife spooks him every now and then.

He is very energetic and active for a dog of his age and loves coming into the shop with me.  He just goes and lays on that piece of cardboard and chews on his toy.  Extremely well natured and well behaved.