MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552

RE: Todays Project - What did you do today? - Mayhem - 02-07-2016

I made some new shoulder bolts for the bump knurler on my mates lathe.  The soft Chinese ones had worn out and the result was a smear, rather than a knurl.  I picked up some O1 and milled the hex and then turned the rest.  Heated them to cherry red and quenched them in some old oil.  I then heated them to the point where the oil burned off and let them cool.  I had to use washers, as the holes were countersunk for some reason. The thread is M6x1.00 and the hex is 8mm.

After heat treating - compared to the original worn out one
[attachment=12681]
All done!
[attachment=12682]

RE: Todays Project - What did you do today? - Roadracer_Al - 02-08-2016

A friend scored a very nice after-market muffler for his bike on eBay for cheap because it was missing it's mid-pipe. He consulted with me and I recommended we build one out of stainless. He ordered the parts -- a pre-bend, a straight section and reducer -- and we had a little garage party putting it together.

What was nice about the build was that no parts were scrapped, all the joints fitted very nicely and we were done an hour before we thought we'd be done.

Normally, you start building an exhaust from both ends and it meets in the middle, and that middle joint is usually the one which takes as much time as the whole rest of the pipe and has a terrible fitting joint anyway. This one came together just so and fairly quickly. As our Brit friends say, I was well chuffed.

RE: Todays Project - What did you do today? - f350ca - 02-08-2016

Was making bearing mounts for a transfer case on the processor and needed to remove a pile of metal. Started with 4 1/2 dia stock and needed to rough bore it to 2.65 ID. My Kenametal boring bar takes a 322? triangular insert, I've always used the two sided regular inserts in it. It does well with maybe .030 depth of cut. Ran across these inserts, no idea what they are called,(help Ken), .1 depth of cut at 500 rpm and ,007 feed rate was effortless with masses of C shaped chips flying.
[Image: IMG_2041.jpg]

Final rough bore, ready to be welded into the case, then final line bored to size.

[Image: IMG_2042.jpg]

RE: Todays Project - What did you do today? - dallen - 02-08-2016

worked on making a screw for a Remington that I'm trying to bring back from the grave

[attachment=12691]

RE: Todays Project - What did you do today? - PixMan - 02-08-2016

Greg,

It's kind of hard to tell but I think you may need TNMG33x inserts for that boring bar, not 322. Those would be 3/16" thick instead of 1/8" thick.

While that's a common insert designation, the specific one I see there is special for boring bars as it give a high positive easy-cutting action in a bore and reduces chatter. The chipbreaker shape that Walter Valenite uses is available in left hand (for boring bars) or right hand (for O.D. turning) and they only have the chipbreaker is only on one side, making it a TNMM. You can use either thickness because your top clamp can reach and you can adjust height. If you get me the nomenclature off the bar I can tell for certain what insert should be in there. If, for example, it's a 1" bar the nomenclature might read "S16-MTONR 3". Insert thickness isn't part of that. Thickness is determined by the depth of the pocket and the total height of the carbide anvil and the cutting insert.

If you were shopping eBay or elsewhere for more of that style insert, look for TNMM332 (or 331)-EL-PN1 or EL-PN2. The difference is in just how deep and tight the chipbreaker shape might be. I can't tell which you may have, but either works as that one did and it's pretty cool, eh?

RE: Todays Project - What did you do today? - f350ca - 02-08-2016

Thanks Ken, please remember I'm insert challenged. This insert is in fact thicker than 322?, probably is 3/16 thick. I'll get the nomenclature off the bar for you.
Cool is putting it mildly, that insert just ate the metal, the lathe has 10 hp but you couldn't really hear load at that .1 DOC. And the chip control was probably the best I've ever had.

RE: Todays Project - What did you do today? - f350ca - 02-09-2016

Hi Ken
Here's a photo of that bar.
[Image: IMG_2045.jpg]

Thanks Greg

RE: Todays Project - What did you do today? - f350ca - 02-09-2016

Had some smaller versions of that insert I was using in the boring bar, so made a 3/4 inch bar for the indexing head.
[Image: IMG_2046.jpg]

Again it cut amazingly well, especially for the length of the bar. Needed about 7 inches to reach into the gearbox.
[Image: IMG_2047.jpg]

RE: Todays Project - What did you do today? - Sunset Machine - 02-10-2016

That's encouraging. One of these days I need to venture into carbide and making a holder is very appealing.

RE: Todays Project - What did you do today? - Highpower - 02-12-2016

While my mill is apart I wanted to look into something that has been bugging me for a couple of years now. Once in awhile my quill would stick when down feeding using the fine-feed wheel. Most often when I tried to come down a few thousandths to a specific depth. The quill movement would start to get stiff, then suddenly jump down much farther than I wanted to go. The outside of the quill is clean and smooth, as is the bore in the head that it rides in. This happened to me before - years ago, before I had installed my power drawbar. Adding some grease to the splines on the spindle made the problem go away.... temporarily.

With the head apart I was able to get a good look at the spindle splines and found several nicks and burrs on the upper portion of the spindle.

[attachment=12696]

The only thing I could think of that would cause this would be the driven spindle shaft hitting a sharp edge inside the belt drive tube/shaft where the mating driving splines are. Even though the ends of the splines are chamfered they do still have an "edge" to them. And my mill has always had a slight rattle sound to it when its running because there is some backlash between the splines. But put a heavy cut on a flycutter.... ho-lee-cow!   Yikes

I cleaned up all the parts and then smoothed out the nicks/burrs on the spindle splines. Holding the drive tube over the spindle I found I could rock it back and forth a bit - top to bottom. Looking further I see that the drive spindle (tube) only has splines in in the center portion of the tube. The bottom of the tube has an oversize counter bore in it for the first 2 inches, then there is 2 inches of splines above that. The top 3-1/2 inches of the tube is also counter bored. I measured the parts and found there is a difference of .070" between the OD of the splines and the ID of the counter bores in the tube.  Slaphead

I'm thinking that would account for the nicks in the splines if the driven spindle is being whipped around inside the tube and flexing because of too much clearance. Bending the spindle would cause the shaft to dig in to the edges of the splines in the center of the tube. Maybe?   Smiley-think005

At any rate I turned some sleeves out of some graphite filled bronze rod (lots of expensive swarf there!) to take out some of the excessive clearance and hopefully hold things in line better. The sleeves are .030" wall thickness so that leaves me with .010" clearance (total) for the splines to run in. At least I hope so.

[attachment=12704]

[attachment=12705]

[attachment=12708]

[attachment=12707]

The spindle brake drum was slightly modified by cutting some flats around the OD to serve as an encoder wheel for a MachTach display. While the brake drum was off I also drilled and tapped it for 2 Helicoil inserts. This way if I ever need to touch-up the paint on my "encoder" I can use a stud-type gear puller to get it off instead of having to pull the entire drive spindle out to get at it.

Got the drive spindle assy back together with new (sealed   Rolleyes ) bearings, ready to go back into the mill. Still need to work on a mount for the IR speed sensor though. Not much room to work with.

[attachment=12710]

[attachment=12711]