MetalworkingFun Forum
Todays Project - What did you do today? - Printable Version

+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Todays Project - What did you do today? (/thread-727.html)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552

RE: Todays Project - What did you do today? - TomG - 04-08-2015

Days of practice and a $3500 inverter TIG welder.

RE: Todays Project - What did you do today? - Roadracer_Al - 04-09-2015

I've been welding aluminum on a hobby level for about 20 years.  I think what that actually means is that I've had about 6 months of experience 40 times over.   Bash

RE: inverter, yes, I'd love to get one. My wife & I moved to Oakland from Maryland 6 years ago -- that would have been the perfect time to sell the trusty old Lincoln SquareWave 175 and buy a newer solid-state machine.... instead, I dragged that heavy lump out here.

RE: casting, yes, that would be a great project. I did some casting with lead when I was a kid, and I understand the process. I actually have a fairly challenging pattern-making project which I'd like to tackle: my '69 Yamaha DT250 is totally stock, and I'd like to cast a copy of a GYT or WebCo performance head for it. It's an air-cooled 2-stroke, the performance head is 2x heavier, with much bigger fins for better cooling than the stock head.

RE: Todays Project - What did you do today? - dallen - 04-09-2015

(04-09-2015, 12:37 AM)Roadracer_Al Wrote: RE: casting, yes, that would be a great project.  I did some casting with lead when I was a kid, and I understand the process.  I actually have a fairly challenging pattern-making project which I'd like to tackle: my '69 Yamaha DT250 is totally stock, and I'd like to cast a copy of a GYT or WebCo performance head for it.  It's an air-cooled 2-stroke, the performance head is 2x heavier, with much bigger fins for better cooling than the stock head.

if you have one to copy the ideal way would be to make a silicon rubber mold of it then make a wax cast from that then do an investment and burn the wax out of the investment.

next up easiest way would be to use cnc and make a wax pattern then do the silicon rubber mold.

hardest way is to make a wooden pattern which would probably have to be a multi part pattern (more than two pieces). Hardest of anyway that you do it would be the core boxes, but with an original you could cast the air passages and such in rubber then make core castings from them.

Anyway you look at it, its not an easy project, but then again others have done harder projects.

DA

RE: Todays Project - What did you do today? - awemawson - 04-09-2015

Hey it's a Sunbeam Alpine - they were a laughing stock when they came out, is it worth making a casting !!!!

RE: Todays Project - What did you do today? - Roadracer_Al - 04-09-2015

Yeah, they weren't fast with the 4-cylinder engine, and I'm sure being featured on Get Smart didn't help their reputation at all.

The suspension was pretty modest, too. They handled OK under normal circumstances, but poorly when pushed. IIRC, they had woefully inadequate roll bars from the factory.

But, I've always loved their looks. I'm slightly envious. I admit, if it were my car, I'd have done either a Tiger clone or put a SR20DET in it.

Regarding the cylinder head, no core box necessary since it's a 2-stroke, all the porting is in the cylinder. The fins are challenging, but it's a simple cope & drag job. I'll probably make a wooden pattern and sand cast it. My idea on the wood pattern is to saw "fin stock" strips on the table saw, then glue up an over-sized stack of them, then use the belt sander to bring it to size & shape, and apply fillets & details such as bolt bosses with Bondo.

RE: Todays Project - What did you do today? - dallen - 04-09-2015

sounds like you got a handle on it, the wood will have to be super smooth for the pattern to pull out but its doable.

DA

RE: Todays Project - What did you do today? - dallen - 04-12-2015

been messing with a little 22 magnum rifle I'm putting together for the shop monster to shoot snakes with.

[Image: stock-work-003.jpg]

The Wood that I'm using for the stock was gifted to me from a forum member. Looks like its going to work out just fine crack and all.
DA

RE: Todays Project - What did you do today? - PixMan - 04-19-2015

Altered the long steel shank of a Walter Screw-Fit adapted B3230.T18.20-26.Z1 precision boring head. The boring head screws onto the tapered, hardened steel shank. The OD of the boring head is 19mm (3/4"), and it's made to bore from 20mm (0.787") up to 26mm (1.0236") using a CCGT050204 (CCGT1.81.51) insert.

The "business end" of the steel shank where the boring head mounts comes down to a little below that 19mm, but I stopped at just a hair over 19mm when I turned it. It was really HARD steel! I think over 55Rc (560HBn) and may have actually been up to perhaps 62Rc. Fortunately I have some Valenite grade 9605 TiAlN coated inserts capable of turning hard steels, no problem. Normally that might be in the range where you go to CBN inserts which I also have, but I prefer using carbide inserts with chip control.

The customer of mine (yeah, a pay job for a change) said the shank cost him "only" $144, so if I screwed it up it wouldn't be a big deal. He needed to reach into a hole by about 3" (76mm), but at an extreme angle so he needed 5-1/2" clear. From there out to about where the original taper started it figured out to be about a 14.2º angle so I used the compound slide at that angle to make the new cone shape. Glad it came out good with no mishaps, because although the steel shank is relatively cheap, that boring head lists for $1,174.00. Ouch. I gotta tell you though, if you ever come across a deal on one those B3230 boring heads are the cat's meow. So smooth!

[Image: IMG_4022-r_zps4qbr9vl9.jpg][Image: IMG_4025-r_zps2lacef2u.jpg]

RE: Todays Project - What did you do today? - EdK - 04-19-2015

Nothing to show but I fixed my compressor. It was leaking as the result of the type of quick change fitting that came on the compressor and the cheap fittings I got from Menards for the air hose. I ended up going to Runnings Fleet and Farm and got all new, made in the USA type 'M' Milton fittings for the compressor and the air hose. No more leaks. I chucked the old fittings into the trash where they belong.

Ed

RE: Todays Project - What did you do today? - Mayhem - 04-19-2015

Nice job Ken but I wonder if this will now make it more chatter prone?