+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: [PROJECT] Filing machine build (/thread-2956.html)
RE: Filing machine build - marfaguy - 12-13-2015
(12-11-2015, 11:45 AM)Dr Stan Wrote: Will this be a variable speed, or a set number of strokes per minute? I have an old scroll saw that would be an excellent starting point for a die filer, but I do not have a clue as to what strokes/minute to use.
I'm planning on getting a variable speed motor rather than setting up some sort of step pulley system. I don't have any experience with scroll saws so I'll leave that to somebody else.
RE: Filing machine build - marfaguy - 12-13-2015
I've made some more progress on this and hope to post more in the next couple of days.
RE: Filing machine build - marfaguy - 12-24-2015
The constructions notes suggest mounting the the base onto the lathe carriage (assuming your lathe carriage has T-slots) to bore the drive shaft. If your lathe carriage doesnt have T-slots ( which mine does not) then you have a couple of choices. One is to use a mill with a boring head or somehow mount the base in the lathe to bore out for the drive shaft bearing. My mill is just shy of being able to mount the base with a boring head AND have a boring bar capable of clearing out the necessary 2.5+ depth. Andy offers some good suggestions for mounting the base in the lathe and then boring the drive shaft.
Heres what I did based on Andys notes. First mount the base so the flattened bottom is vertical with the already milled drive shaft end surface resting on the bed of the mill.
[attachment=12472]
Note: I had previously welded up a right angle plate that after machining requires about .003 shimming to make it just about perfect vertical off of the mill table.
With the Plug end now facing up I milled off the horizontal surface just enough to clean it up over most of the surface and then bored the recess for the plug and drilled/tapped for the plug bolt circle.
[attachment=12473]
I then turned a spigot to fit the plug end and mounted it in the mill to drill for matching bolt circle holes. [attachment=12474]
I then bolted the spigot to the base and mounted it in the lathe
[attachment=12475]
[attachment=12476]
I didnt grab a picture of it but first tried to bore horizontal shaft without the steady rest. That didnt seem to be working very well so I took a few vey light cuts on exterior and then used the steady rest.
[attachment=12477]
I then bored the base 1.25 +- .001 for the bronze bearing.
RE: Filing machine build - Highpower - 12-25-2015
Nicely done marfaguy.
No doubt about it, swinging a heavy bulky part like that in the lathe takes some planning to do it safely and accurately.
One of the items on my wish list is to make some sort of t-slot jig to fit my lathe cross slide. I began thinking that is a feature every lathe should have since the first time I saw a cross slide equipped with t-slots.
RE: Filing machine build - Roadracer_Al - 12-25-2015
Willie, I couldn't agree more about a boring table / t-slot table. -- my 16x40 doesn't have one, and I've been scheming how to attach one.
RE: Filing machine build - Highpower - 12-25-2015
(12-25-2015, 12:49 PM)Roadracer_Al Wrote: ....., and I've been scheming how to attach one.
Well hurry up Al, so I can copy it!
On second thought, no rush. I've still got a number of Tom's projects I want to make for my lathe too. I've got a lot of catching up to do...
RE: Filing machine build - ncollar - 01-21-2016
I have a bar stock build of a die filer, those interested in the plans give me a PM at nel2lar (AT) yahoo (DOT) com
Replace with the appropriate punctuation marks.
Nelson Collar