+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: General Metalworking Discussion (http://www.metalworkingfun.com/forum-6.html)
+--- Thread: Asong AS-235 power feed?? (/thread-1336.html)
RE: Asong AS-235 power feed?? - stevec - 05-14-2013
Can you not measure the voltage with a VOM? Are you thinking of scraping the " plastic light tube/fiber optic." and installing the LED in the case of the power feed?
RE: Asong AS-235 power feed?? - Highpower - 05-14-2013
(05-14-2013, 07:06 AM)stevec Wrote: Can you not measure the voltage with a VOM? Are you thinking of scraping the " plastic light tube/fiber optic." and installing the LED in the case of the power feed?
That's exactly what I was thinking Steve. Yes, I could have taken it apart to measure it with a VOM, but I was fairly sure it was 110-125VAC. I just didn't want to take it apart now, and have it down until I could obtain another lamp for it. Even though the original light is working you can't see it from above. You have to be down at eye level, which basically means on your knees on the floor. I'm constantly forgetting to turn the power switch off because I can't see the dim glow when I'm standing in front of the mill.
Rather than replace the original neon bulb and light pipe with a LED, I think it would be easier to replace them with a 120V panel mount/pilot light. They come in neon or incandescent styles and can simply be soldered to the board.
Something like this:
![[Image: SSI-LXR9126SYD110V.JPG]](http://media.digikey.com/Photos/Lumex%20Photos/SSI-LXR9126SYD110V.JPG)
RE: Asong AS-235 power feed?? - Mayhem - 05-14-2013
Personally, my approach is to isolate the power to each machine, ensuring that any accessories are powered down as well.
The annoying one is the cordless drill battery that spends a week on charge
RE: Asong AS-235 power feed?? - EdK - 05-14-2013
Willie,
You may want to look at a style like this one where the light protrudes out so you can see it easier.
Ed
![[Image: Q8P3BXXG12E.jpg]](http://media.digikey.com/Photos/APEM%20Comp%20Photos/Q8P3BXXG12E.jpg)
RE: Asong AS-235 power feed?? - Highpower - 05-14-2013
(05-14-2013, 08:46 AM)Mayhem Wrote: Personally, my approach is to isolate the power to each machine, ensuring that any accessories are powered down as well.
The annoying one is the cordless drill battery that spends a week on charge
Well, I'm half way there Darren. My lathe and mill share a 120V and 240V circuit which get turned off if I'm not using the machines. The power panel is already full so I can't split them up. It's not a problem since I don't use both machines at the same time. I just don't like having power running to the table feed when I'm using the lathe - because I forgot to turn it off.
I'm guilty of the battery charger thing as well.
RE: Asong AS-235 power feed?? - f350ca - 05-14-2013
Mine gets left on most of the time, that little neon light is hard to see in the dark, especially with the usual layer of protective grim my machines seem to get.
RE: Asong AS-235 power feed?? - Highpower - 05-14-2013
(05-14-2013, 09:42 AM)EdK Wrote: Willie,
You may want to look at a style like this one where the light protrudes out so you can see it easier.
Ed
I agree Ed, The only problem there is you have to be careful of the overall length. I don't know how much space there is inside the housing. May have to mount it externally.
RE: Asong AS-235 power feed?? - Highpower - 05-14-2013
(05-14-2013, 11:56 AM)f350ca Wrote: Mine gets left on most of the time, that little neon light is hard to see in the dark, especially with the usual layer of protective grim my machines seem to get.
Exactly! Fortunately the newer model I put on the knee has a very bright ring light surrounding the rapid traverse button. That one I can see from the other side of the shop.