+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: P&W 1830 Radial in 1/6 scale. (/thread-573.html)
RE: P&W 1830 Radial in 1/6 scale. - EdK - 04-23-2013
(04-23-2013, 05:36 PM)Bill Gruby Wrote:(04-23-2013, 05:31 PM)EdK Wrote:(04-23-2013, 04:09 PM)Bill Gruby Wrote: The casting needs finish work now, first the lathe , then mill, and back to the lathe. For ease of finding the center in each machine this tool was fabricated. It will also keep everything flat.
"Billy G"
I'm not sure what I'm looking at Billy but it looks impressive none the less.
Ed
Ed;
The heavy aluminum piece in the chuck is the fixture. It is made with that much mass to absorb vibration while cutting the thin casting. The casting is on a spigot and bolted in the center. This fixture will allow me to bore the offset holes for both distributors. and any other mill work. Then back into the lathe for final cuts.
"Billy G"
Billy,
OK, I took a closer look at the picture and now I see what's going on. Sorry for the
Ed
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 04-23-2013
There are times when things cannot be done by normal procedures. This is part of the machinists job to figure these things out. My father used to try to tell me that 70% of a machinists job is accomplished by imagination. I will never forget those words, nor will my son.
I enjoy the questions Ed, ask any time.
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 04-24-2013
Same fixture being centered on the Rotary Table. From here we go horizontal to bore the two distributor shaft holed. They are offset .625 from center on the Y axis and angled at 11 degrees.
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - Mayhem - 04-24-2013
Looking good Bill.
Were these engines throttled by varying the ignition timing?
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 04-24-2013
Thank you Darren. The two shaft holes are finished. Now back to the lathe.
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - DaveH - 04-25-2013
Fabulous work Billy
DaveH
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 04-29-2013
Distributor shaft housings done without shaft holes. (660 Bronze) They can't be drilled till the housings are pressed into the lower distributor bodies. The last pic is where I begin today, the lower bodies.
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - EdK - 04-29-2013
Billy,
Is that model airplane going to fly or is it for show only?
Thanks,
Ed
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 04-29-2013
Ed;
At this point it will be a runner but no plane in it's future. I'm building it to see if I can .
"Billy G"
RE: P&W 1830 Radial in 1/6 scale. - Bill Gruby - 04-29-2013
4 jaw turning is done. Time to put in the ER-40 Collets.
"Billy G"