+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Welding & Casting (http://www.metalworkingfun.com/forum-9.html)
+---- Forum: Blacksmithing (http://www.metalworkingfun.com/forum-29.html)
+---- Thread: Coke Forge Build (/thread-2189.html)
RE: Coke Forge Build - f350ca - 11-20-2014
The 36 grit isn't used over here, if we're going to do work that rough we just drag the part down a gravel road behind truck.
RE: Coke Forge Build - krv3000 - 11-20-2014
rob you gowing to jhons on sat
RE: Coke Forge Build - RobWilson - 11-20-2014
(11-20-2014, 04:31 PM)krv3000 Wrote:
Aye ,more than likely mate , you need out ?
Rob
RE: Coke Forge Build - EdK - 11-20-2014
The 36 grit must have that same toxic substance the China suppliers used in the dry wall they sent over a few years ago that was making people sick. We don't allow that stuff here anymore. Good luck with that.
Ed
RE: Coke Forge Build - Mayhem - 11-20-2014
Hi Rob - could I suggest that you start a different thread for the linisher build?
RE: Coke Forge Build - krv3000 - 11-21-2014
yep just fill the van up blue role and spray
RE: Coke Forge Build - RobWilson - 11-24-2014
Made a start on the butterfly valve , First off I slapped a 1" x 4" slice of EN3876 steel into the CUB Lathe for a wee bit of spinning about .
![[Image: P1080473_zps0fd9fd8d.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/P1080473_zps0fd9fd8d.jpg.html)
Next off two flats milled on the Viceroy mill .
![[Image: P1080478_zpsc90799a5.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/P1080478_zpsc90799a5.jpg.html)
Then onto the Aciera F3 to do the slots . Using a surface gauge to clock the job in , as I already had the PCD set .
![[Image: P1080481_zpsa72cc379.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/P1080481_zpsa72cc379.jpg.html)
![[Image: P1080482_zpsa39e7d2c.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/P1080482_zpsa39e7d2c.jpg.html)
![[Image: P1080490_zps10ec0098.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/P1080490_zps10ec0098.jpg.html)
Then onto the drill to have a couple of holes poked in ,
![[Image: P1080496_zps0d9d0da9.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/P1080496_zps0d9d0da9.jpg.html)
Body done .
![[Image: P1080497_zpscb3b6c55.jpg]](http://s1066.photobucket.com/user/RobWilson100/media/Forge/P1080497_zpscb3b6c55.jpg.html)
Rob
RE: Coke Forge Build - awemawson - 11-24-2014
Looking very nice Rob !
Not come across EN3876 before - is that a stainless steel?
RE: Coke Forge Build - DaveH - 11-24-2014
Rob,
Very nicely done - excellent job
Liked the set up to drill and ream the hole(s) Well photographed
DaveH
RE: Coke Forge Build - EdK - 11-24-2014
As usual, very nice Rob.
Ed