+- MetalworkingFun Forum (http://www.metalworkingfun.com)
+-- Forum: Machining (http://www.metalworkingfun.com/forum-5.html)
+--- Forum: Projects (http://www.metalworkingfun.com/forum-7.html)
+--- Thread: Press brake for 20 ton hydraulic press (/thread-2127.html)
RE: Press brake for 20 ton hydraulic press - starlight_tools - 07-06-2014
(07-06-2014, 10:55 AM)arvidj Wrote:starlight_tools Wrote:Arvid
What is the diameter and C-C distance of the two round bars that are used as the bottom dies on your unit?
Also do you know how heavy of plate it was rated to break?
Thanks
Walter
Walter,
I do not remember what they claimed it was capable of bending. I remember seeing charts that suggest the thickness and width that 20 tons will bend but I can't find the link at the moment.
Here is a picture with the small die in place. You can see it just fits between the two rods that are welded to the base plate.
Here is a picture with the small die removed.
I measured the width of the small die so that defines ... more or less ... the gap between the two rods.
And then I measured the diameter of the rod. Note that I must have hit the reset when I went to take the picture but it was 1 inch in diameter.
I hope that helps.
Arvid
Arvid
Thanks
I found my charts and here is the correlation between top width and capacity. Any die under 1" is 90 Deg, and over is 85 Deg.
1-1/4" with 3/16R 9 Ga
1-1/2" with 3/16R 3/16
2" with 7/32R 1/4
2-1/2" with 1/4R 5/16
3" with 5/16R 3/8
4" with 3/8R 1/2
http://iroquoisiron.com/wp-content/uploads/2012/05/press-brake-tooling.pdf
The round bar that I have set aside for this project is 1-3/4 " dia.
I figure that if I mount them 6" C-C gives me 4-1/4 opening and if I mount them on top of 3/4" flat bars, I should be able to handle 5/8 plate, based on using a press that is 50 Ton. Then I can have a drop in die like yours for the smaller sizes.
Walter
RE: Press brake for 20 ton hydraulic press - DaveH - 07-07-2014
5/8" plate and 50 tons - WOW!
DaveH
RE: Press brake for 20 ton hydraulic press - starlight_tools - 07-07-2014
(07-07-2014, 03:44 PM)DaveH Wrote: 5/8" plate and 50 tons - WOW!
DaveH
there is a limit as to how wide you can bend 5/8 at 50 Ton, and I doubt I would ever need to bend that wide or that thick about 3" wide with a die that is 10" at the top, but should have no problem with 1/2" x 10 inch as per the quote I got from Iroquois Iron when I inquired about there commercial 24" bender for a client based on a 4" die or 3/8" x 18" with a 3" die.
Walter
RE: Press brake for 20 ton hydraulic press - DaveH - 07-29-2014
I decided to make a couple of removable bottom dies. 'Make' ...... well I cut the angle iron to length and painted them.
The smaller angle fits in side the larger angle the idea being to get a smaller radius on thin material - 2mm thick.
[attachment=8930]
[attachment=8931]
DaveH
RE: Press brake for 20 ton hydraulic press - mfletch - 07-30-2014
That's a good idea Dave thanks
RE: Press brake for 20 ton hydraulic press - DaveH - 03-07-2015
I (we) did some bending 3 pieces 100mm wide x 150mm long x 2mm thick ordinary sheet steel.
They came out quite good the press brake made a nice job of them. The guy I was bending them for was very happy which at the end of the day is all that counts
[attachment=10200]
[attachment=10201]
[attachment=10202]
However it is not that easy to judge when it is at 90 deg took 3 -4 goes per piece.
[attachment=10203]
[attachment=10204]
DaveH
RE: Press brake for 20 ton hydraulic press - EdK - 03-07-2015
Dave.That reminds me that I've got to get my press brake put together. Welding weather should be starting soon.
Ed
RE: Press brake for 20 ton hydraulic press - Mayhem - 03-07-2015
There are no welding seasons Ed - procrastination is not weather either
RE: Press brake for 20 ton hydraulic press - stevec - 03-07-2015
Darren, I'm sure he meant "whether" as in "whether to weld or not"
Steve
RE: Press brake for 20 ton hydraulic press - Highpower - 03-07-2015
Very nice job Dave.
So....... those welds held up after all eh?
